Model #91130169690 KENMORE Wall Oven, Gas

  • Control Section
    3 Results
  • Wire Harness And Components
    3 Results
  • Burner Section
    3 Results
  • Body Section
    3 Results
  • Door Sections
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Oven display does not work 91130169690 Kenmore 24"(gas built-in oven

A:

Thank You for contacting ManageMyLife.com

I understand your frustration when the display no longer works. The control panel/clock is a non-servicable part. You would need to replace this part. I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link below to be taken to the page.

Electronic Oven Control For Model 911.30169690

If you have further questions please let me know.
Thanks for visiting ManageMyLife.com

Read More
Desirea -
Sears Technician
October 27, 2013
Q:

Gas Oven not working.

A:

I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Alina F. -
January 21, 2012
A:

The F3 code indicates that you have a problem with the oven temperature sensor probe. If you are still seeing that code, then I recommend that you shut off the house circuit breaker for the oven and access that probe as shown in the image below. You can test that sensor using a volt/ohm meter as shown in this video: Oven Sensor Testing . That sensor should measure around 1100 ohms at room temperature. If it is bad, it will need to be replaced. You can order that part from the Sears PartsDirect website. The part number for that sensor is WB21X5301.

If you do not see that F3 error code, then you may have a problem with that igniter on the oven burner. The theory of operation for that ignition system is shown in the image below. You may have a weak igniter. That igniter may work properly from a cold start but it may not be working good enough to ignite the burner or subsequent re-ignition attempts. In that situation, you would need to replace that igniter (part WB2X9154).

These tips may help you diagnose and repair your oven failure. If you need more help, reply with additional details.

If you get to a point where you need to have a service technician examine and repair the oven, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 23, 2012
See more answers
Q:

F3 error reading on my Kenmore gas stove

A:

Error codes can certainly be concerning. While your waiting for an expert to respond, I attached some links that will help exp[lain the error code. I hope this helps!

Read More
Jackie S -
August 11, 2011
A:

As you can see from the answers Jackie S sent, the F3 error code indicates a problem in the sensor circuit.

Since you don't get the error code until the oven has heated up, I suspect the problem is in the connection where the oven sensor connects to the range wiring harness. You can access this connector by removing the 2 screws that hold the sensor to the rear wall of the oven and pulling the wires and connector into the oven.

You can eliminate the connection and connect the wires with ceramic wire nuts. If this doesn't correct the problem, you should probably replace the clock.

If you have questions, reply on this link and I will be glad to help.

You can order parts for your range at Parts Direct

Read More
Jimmy K -
Sears Technician
August 12, 2011
A:

Thank you for your reply....Can you tell me if the connection that you are talking about is one that has wire nuts connecting the sensor to the harness...How would I "eliminate" the connection? Are there wire nuts? Are you saying that this connection is loose? and that by using ceramic wire nuts it will be a tighter connection?... what does the clock have to do with this problem...please forgive me for my "stupidity" but I am electrically challenged so I need extra help...by the way...sometimes the F reading is F2 or F5 ...does that mean that there might be a different problem? Should I turn the electric off before I unscrew the sensor and pull the wires thru? Sandy

Read More
Sandy -
August 12, 2011
A:

I apologize for not being clear. The connection between the main harness and the oven sensor is a plastic connector. Over time and through heating and cooling, the terminals inside the connector begin to make a weak connection. You can cut the connector off the wires and use ceramic wire nuts to replace the connector. The clock on your oven is capable of producing F2, F3, and F5 error codes. If the clock fails it might produce any error code. By all means turn off the electric before removing the sensor. Thanks for asking the questions.

Read More
Jimmy K -
Sears Technician
August 12, 2011
A:

Thanks Jimmy ...things are much clearer now...I will try redoing the sensor connection and if that does not fix the problem, I will get back to you about replacing the clock... Thanks again,,,Sandy

Read More
Sandy -
August 12, 2011
A:

Good luck Sandy. Thanks for using Manage My Life.

Read More
Jimmy K -
Sears Technician
August 15, 2011
A:

Hi Jimmy...I haven't had time to put the new connectors on the sensor but I plan to do that today...Wish me luck...if that doesn't work I will get back to you...OK? Sandy

Read More
Sandy -
August 15, 2011
A:

Sandy, install the wire nuts so they are not side by side and they will go through the small opening on the back of the oven easier. Cut the wires so they are uneven. One will be in front of the other. I hope this makes sense to you.

Read More
Jimmy K -
Sears Technician
August 15, 2011
A:

Yes...I know exactly what you mean...thanks...S

Read More
Sandy -
August 15, 2011
A:

Jimmy it looks like the problem is going to be in the clock/oven control assembly... can you tell me how to install this? Is it going to be difficult? Sandy

Read More
Sandy -
August 15, 2011
See more answers