Model #88 MAJOR Kitchen Equipment

  • Replacement Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

i have a ge refrig model gfss6kkyass, the temp control and ice maker display panel is showing 88 degrees and i can't change the setting or make ice.

A:

I apologize, to hear you're having this problem with your fridge. Our refrigerator is a major appliance that we depend on everyday. I have done some research and located a link similar to your issue that may be helpful until an Expert responds. Hope this helps and thank you for using Manage My Life!

Read More
Carmen G -
August 19, 2012
A:

Hi,

Thank you for your question. It is concerning when the refrigerator is not functioning correctly. With the 88 88 showing on the display you are getting a error code. If the icemaker quit working, on this refrigerator the icemaker is the front component in the refrigerator, in other words it is the controlling device. I am giving you the codes. Unplug the refrigerator and reconnect it. The code should come up and then you will know what the processor is seeing or not seeing. Front panel access to the codes is also on the chart but I would like to do a hard restart to try to clear the codes, by disconnection from electricity.
The icemaker is still plugged into the harness, correct. Just turn the icemaker off at the icemaker itself.

I hope this is helpful. If I may be of further assistance please include more details in a reply to this post.

Read More
Bill__W -
Sears Technician
August 20, 2012
A:

ge refrigerator model #gfss6kkyass ice maker will not make ice .how can you trouble shoot this being ice maker module problem or the ice maker it self ?

Read More
bill -
January 23, 2016
See more answers
Q:

Whirlpool Duet Model WFW9151YW00 Error Code WFW9151Y00

A:

Thank You for choosing Sears PartsDirect.com. I regret to hear that you are having issues with your washer and do understand your frustration. Glad to help out. Im looking at your model number WFW9151YW00. 
For F8 E1 I recommend having the water valve tested and make sure that both hot and cold water solenoids are opening and closing properly. F3 E2 is an indication of a water temperature sensor error, or Heating Circuit failure. Check the Water Temperature Sensor and check connections to the Water Temperature Sensor. Also make sure there is nothing lodged or jammed in the pump area.

Click here for owners manual and other literature.



Read More
Sherman_G_Wallace -
Sears Technician
January 10, 2014
A:

The F3E2 indicates that the control detects a problem with the water temperature sensor. You can enter the diagnostic test mode by selecting 3 different buttons (except the POWER button). Keep track of which is button 1, 2 & 3. Press the buttons in order 1,2,3,1,2,3,1,2,3 within 8 seconds after pressing the first button. The control should go into the diagnostic test mode and display the saved error codes. Press the 3rd Key to advance through the saved error codes. (Write down the saved error codes). After the last code is displayed, the digits 88 will appear in the display. Press the 2nd Key to start an automated test mode. Exit the diagnostic test mode by pressing and holding the 1st Key for 5 seconds or the Power Key. Unplug the washer for 1 minute after exiting the diagnostic test mode. You can check the temperature sensor by unplugging the washer and removing the back service panel. The temperature sensor is at the bottom back of the tub. Check the wiring connections. Test the sensor using a volt/ohm meter. It should measure around 10 to 15K (10,000 - 15,000) ohms at room temperature. If the resistance of the temperature sensor is way off, then you will likely need to replace that component. If the sensor is okay, then you could have a problem with the wiring harness or the electronic control board in the washer. If you need more help, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
January 10, 2014
A:

cuales son los botones 123 para modo diagnostico

Read More
virgo -
January 14, 2015
A:

tengo un problema con este modelo 9151 me sale error f6 y despues e1

Read More
virgo -
January 14, 2015
A:

se puede reparar o lo boto

Read More
virgo -
January 14, 2015
A:

I have the same problem with my whirlpool duet washer, we checked the wiring in the back and everything looks good. We even changed the temperature sensor and we are still getting the same f3 e2 error code. Don't know what else to do please advise

Read More
Martha -
February 24, 2015
A:

washer model wfw9151ywoo when it turn on it say 1 minute let i try reset and diagnose apeal : 88 i do not see any thing. please help

Read More
hans -
March 07, 2015
A:

I have the same problem with E2F3 on this model. I changed the Temperature Sensor and it's still doing the same thing. I'm beginning to believe this model us just a defective piece of garbage. I've searched online, seen how many people have this problem and have found NO solution to it. I want to try the diagnostic test that Lyle W. posted above but it's as clear as mud. I am very computer literate but that needs to be much more explanatory and concise.

Read More
Karen -
May 09, 2015
A:

I tried all sorts of buttons as indicated above, no diagnostic mode comes up. Has anyone else had luck with the diagnostic mode?

Read More
Karen -
May 09, 2015
A:

I tried pressing 123 123 123 and 88 appeared and I checked the codes and F3 E2 then LF appeared and would not go any further and 88 would not appear in screen,

Read More
roger -
December 16, 2015
See more answers
Q:

Maytag dryer model# MEDB200VQ0 won't start.

A:

Thank you for your question and I understand your concern.

Go back into the diagnostic test following the instructions in the tech sheet and after the 888 displays and go out, open the door and see if an alphanumeric number displays and then shut the door to see if will cause a beep and 888 to display. If it does not, it could have a faulty door switch or the new control is faulty. Based on you details, I assume no fault/error code displays after entering the diagnostic test. You may want to re-install the old machine control board and see if responds any differently. If the old machine control acts like the new one, check the door switch and the thermal fuse for continuity with an ohm meter. It should display a fault/error code if it detects any failures.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

Read More
Joey S -
Sears Technician
September 03, 2013
A:

Joey, thanks for the response. You're right, there are no fault/error codes displayed. I tried opening the door after entering the diagnostic mode and nothing happens. When I close the door, still nothing. I have not tried re-installing the original machine control board yet. I am going to be away for a few days so I will try that when I get back. Also, I wanted to ask if there is a way I can by-pass the door switch for troubleshooting purposes? Thanks again for your response.

Read More
Rodger Poirier -
September 05, 2013
A:

Roger: It's beginning to sound like a possible faulty door switch. When the door is shut, the door switch connects the white wire with the blue wire. You can jump the blue and white wire together and then see if will start. I added an image below of the wiring diagram. I hope this is helpful.

Read More
Joey S -
Sears Technician
September 05, 2013
A:

Joey, I tried by-passing the door switch. Same result. Tried re-installing the original board and it behaved the same as the new one. Upon entering diag mode, all indicator lights come on and 888 is displayed. Then the lights all go off but nothing comes back on. Then when I push the button I used to enter diag mode a "CO" is displayed in the estimated time remaining area. I haven't been able to find out what "CO" means? Any thoughts? Thanks

Read More
Rodger Poirier -
September 10, 2013
A:

Rodger: The "C0" is not a known code or a listed code. Based on everything you have tried it sounds like the user interface is faulty. Try the Console and Button test per the tech sheet and see what happens.

Read More
Joey S -
Sears Technician
September 11, 2013
A:

I also have the same exact problem and have done the exact same steps with no luck. Any other suggestions?

Read More
kevin -
September 17, 2013
A:

Kevin: If you have done everything recommended above in the previous response, locate the tech sheet in your washer and perform the Console and Button test. If you cannot locate the tech sheet, reply with your model number and I can provide the instructions.

Read More
Joey S -
Sears Technician
September 19, 2013
A:

Joey. I tried the console and button test and nothing happened. I can get into the diagnostic mode and it brings up the 8:88 and as soon as I press a button all of the LEDs go out. If I press again the LEDs come back on for a few seconds and then it brings that CO code back up and is stuck there until i power down the dryer. Looks like a should replace the user interface board?

Read More
kevin -
September 19, 2013
A:

Kevin; Based on your symptom and details I suspect a faulty user interface. Replacing the user interface will most likely resolve the issue.

Read More
Joey S -
Sears Technician
September 20, 2013
A:

If you look around on the web you can find other people with this model dryer (MDEB200VQ0), experiencing the same issue (dryer won't run and also fails to report known diagnostic codes after a simple power failure at the home). Unfortunately others with this issue have reported that the issue still persist after installing a new interface board and a new control board (about $500 in parts). I have this issue and have dissembled our dryer and tested all its components except for these boards, and the other items all check out according to tech sheet. But I can't decide to order new boards when they cost so much and can not be returned after being installed, while others report they don't fix this issue. Since our dryer is only 5 years old (and the older reports of this issue involved dryers only a couple years old) it makes since for us to buy a new dryer and to never purchase Maytag or any other Whirlpool brands again.

Read More
Caroline -
November 16, 2015
See more answers