Model #87 HOOVER Attachments (Vacuum)

  • Hose, Cleaningtools
    3 Results
  • Mainhousing
    3 Results
  • Motor Assembly
    3 Results
Find part by diagram >

Question and Answers

Q:

kenmore stove model no 911.4652192kw8.7 door won't unlock, had to stop during cycle, pressed buttons and f2 came up, pressed more buttons, now door wont unlock

A:

Hi there, I understand how frustrating you must feel not able to use your Kenmore stove. I see that someone has asked a similar question to yours on Manage My Life's website. I have attached the link below. Hope this works!

Read More
Salina L -
July 06, 2010
A:

The "F2" fault code implies the oven temperature exceeded 590 degrees with the door in the unlocked position or it exceeded 990 degrees with the door locked. If the actual over temperature condition occurred it may have a failed control board. It could also have an open thermal switch or high resistance connection in the temperature sensor. (See image below.)

Based on your symptom I recommend calling a service technician to diagnose and repair your range or you may want to think about replacing the range rather that having it repaired.

I recommend calling 1-800-4MY-HOME or 1-800-469-4663 to set up a service appointment if you decide to have it diagnosed and repaired.

Read More
Joey S -
Sears Technician
July 09, 2010
A:

Should a 22year old kenmore be subjected to the high heat that occurs when cleaning an oven (9114652192)?

Read More
Elizabeth -
January 26, 2016
A:

Should a 22year old kenmore be subjected to the high heat that occurs when cleaning an oven (9114652192)?

Read More
Elizabeth -
January 26, 2016
See more answers
Q:

New Prgressive Vaccum 21514. When I slide button for the powerhead to come on the main motor turns off. How can I correct this?

A:

I can understand how frustrating it might be when your vacuum is not working correctly. The more information you provide the better result you will get by the expert. The suggestion that i have for you is to place the full model number so that way he can answer your question more specifically.

Read More
celene -
December 10, 2010
A:

Model # 116.2151.4010

Read More
Aubie 3 -
December 10, 2010
A:

Thank you for your question.

Not having the vacuum motor running when the power mate is on is a concern.

If the vacuum motor works on the hard floor settings then we know the suction motor circuit is ok.

  • It sounds like the problem is in the slide handle switch and will need to be replaced.

If the unit is still under warranty I would suggest that you take just the handle hose assembly in to be repaired.

If it is not under warranty then we will need to take the handle assembly apart and change the switch out.

  • You will need to remove the 3 to 5 screws in the handle half and split the handle making sure you locate how the switch is captured between the two halves of the handle.

NOTE; how the switch is wired before you replace with the new switch to make sure have it pointing the right direction.

The part number for the switch assembly is;KC87GDKNZ000 and you can purchase it from;Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired by a Sears technician. Here is a link that will provide the nearest drop-off locations: [Sears Home Services | http://services.sears.com/shs/category/repair?sid=MMLxexpertxmerch

I hope this will help with your vacuum issue.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
December 11, 2010
A:

Thank you--- it is still under warranty so I will take it in. Thanks again for your reply.

Read More
Aubie 3 -
December 11, 2010
A:

Hi Sam, My issue is I can't get the 2 halves of the wand apart. I'm afraid to pull too hard, otherwise it seems like it may break. Does it slide apart or do you pry it apart. If prying, where do you start to make it easiest to separate? I Only need to replace the spring for the wand release button, so should be trivial once I get it apart. Thanks!

Read More
keith -
January 09, 2016
See more answers
Q:

Canthe gas supply be stut off to a single burner ? JGBP87SEM3SS Ge Gas range


Top Parts