Model #831299282 PROFORM Treadmill

  • Frame
    3 Results
  • Control Panel
    3 Results
Find part by diagram >

Question and Answers

Q:

I have a Proform 830 QT treadmill model # 831. 299282 and I would like to calibrate it.

A:

I understand that you want to calibrate your Proform treadmill. I have done some research and I was able to locate your owners manual which should have some information on how to re-calibrate your treadmill. I hope this is helpful. Have a great day!

Read More
Alina -
March 09, 2013
A:

Thank you for your question.  I will be happy to assist you with the calibration mode. I posted an image below that shows how to enter calibration. Click on the image to enlarge it. If you do not see the image, please copy and paste the following link to be taken to the original site to view the image. http://www.managemylife.com/mmh/questions/337606-proform-830-qt-treadmill-model-831-299282-calibrate I hope this is helpful. Please let me know if you need further assistance.  Thank you for using Manage my life. Mark.

Read More
Mark T -
Sears Technician
March 11, 2013
See more answers
Q:

My Proform treadmill's incline is stuck in uppermost position

A:

When the Proform treadmill is not functioning properly, managemylife.com has a solution to your problem. A similar question was answered in the link provided below. Hope this helps while waiting for additional information. If you decide on service, that link is also available below.

Read More
Anna T -
January 11, 2013
A:

Does the machine make any noise when you try to operate the incline? If it does then it may be that the incline motor is mechanically stuck. If there isn't any noise then I suspect a problem with the board that sends power to the incline motor.

There are many different things that could cause the incline to stop functioning. Because of the complexity of this type of problem and the high voltages involved with the machine, you may want to consider having a technician come out to see about this problem. If you're okay around electricity and have a meter, you can open the motor hood up on the treadmill and use the schematic (under the motor hood) to check for voltages at the incline motor when you press the button. If you determine that the motor has voltage to it but it doesn't move then it is mechanically stuck. These motors are not really serviceable, so if it's stuck you'll need to replace the motor assembly.

Thank you for using Manage My Life!

Read More
Wade_B -
Sears Technician
January 13, 2013
See more answers
Q:

How can I replace the walking belt on my Sears ProForm 830QT Treadmill, model # 831-299282.

A:

I think its great that you are wanting to do some repairs on your own and I will be happy to help. I did some research and I was able to find a link that will guide you with your project. I hope this helps with your treadmill repairs while you wait for your expert response.

Read More
Joseph P. -
August 14, 2012
A:

Thank you for your question on having the correct instructions for changing the walking belt on the treadmill.

I am sorry that I do not have any access to printed instructions on replacing the walking belt on this treadmill. There are a number of videos on the web to help with replacing the walking belt.

Here is a similar model to yours that may help you. Treadmill walking board replacement .

You will not need to remove the board as shown but it should help you with replacement of the walking belt.

You will need to remove screws # 65 completely from the rear roller end cap and any screws that may hold the end cap to the frame.

Then remove the right side foot rail #41 by removing 3 screws.

The locate the screws #47 under the frame that secure the right side of the walking board to the frame rail. Once you have the side of the walking board loose and the front and rear rollers removed then you should be able to slide the walking belt from the walking board.

Slide the walking belt over the walking board and replace all screws to secure the walking board to the bed.

Re-install the front and rear rollers into the walking belt and install the rear end cap with the rear roller adjustment screws #65 and install the front roller that you have already removed. Then you will need to adjust the rollers to tighten the belt and align so it will track in the center of the walking board.

Please let me now if you need more help.

Sam A.

Read More
Sam A -
Sears Technician
August 17, 2012
See more answers

Top Parts