Model #831297120 LIFESTYLER Treadmill

  • Unit Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Treadmill starts then stops with EEEEEEE in the window, but then would work. Now won't work at all. 831297120 Lifestyler Lifestyler 6.0 treadmill

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your treadmill. Upon researching model831297120; The EEEE code is telling you the console is getting no information from the speed sensor on the treadmill. If the motor is not running the speed sensor can't send information to the console.

Several things can cause the treadmill to stop running. The motor, power board, motor controller, console, or a broken wire could be causing the problem.

The console and the motor for your treadmill are no longer available for ordering. The motor controller and the power board are available to order.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
March 09, 2015
Q:

Treadmill starts and runs about 3 seconds then stops with EEEE in speed field.

A:

I understand that your treadmill runs for about 3 seconds and then after gives you receive the error code EEEE. I have taken some time to research your question here on the Manage My Life website and I noticed that someone else had asked a similar question with a posted response from an expert. I attached the link below if you are interested in viewing. I hope the link that I provided is helpful.

Read More
Alina F. -
January 27, 2011
A:

Thanks! I have downloaded chart. Will check it out.

Read More
laura -
January 27, 2011
A:

The error code you're getting typically will indicate a problem with the speed sensor. The sensor shows to be located on the right side of the front roller. There were 2 used at the time this machine was built. The schematic for your model shows it to be a disc and sensor. The sensor reads the disk as it spins. You will need to remove the motor hood and locate the sensor and disk assembly. Make sure it is clean as dust tends to build up and cause this type of problem.

If the disk or switch is broken, there is no repair for that as the assembly is no longer in production. More than likely you will find that the disk is just covered with dust and needs to be cleaned off. Make sure to unplug the treadmill from the wall before you remove the motor hood.

Thank you for using Manage My Life!

Read More
XX Wade_ -
Sears Technician
January 27, 2011
A:

Hello Experts, I cleaned the speed sensor and the disk. Still does not work. I unhooked sensor and started the treadmill. Did the same thing as when it was hooked up. Sure hate to give it up, but no other alternative if can not be fixed. Bought it new, so guess it is time to give up the ghost. Thanks again for all your help. I really appreciate it.

Read More
laura -
February 02, 2011
A:

It certainly sounds as if the sensor has failed. I checked around to see if there is an alternative sensor and I cannot find any information on a sensor that will work as a replacement.

Read More
XX Wade_ -
Sears Technician
February 03, 2011
A:

Thanks for all the help. Like I said, it is time to give up the ghost. At least I found out there wasn't anything I could do to repair it before I put out a lot of money trying. You have been a great help and it is well appreciated. Signing off now.

Read More
laura -
February 03, 2011
See more answers
Q:

looking for owners manual for treadmill

A:

Owner's manuals can be hard to hold onto over time. They disappear into drawers, closets, the garage and finally thin air. I understand how it feels trying to find one after so much time passes. I did find some information available in the parts list at Sears Parts Direct. I attached the link below. Hopefully the expert has other resources.

Read More
Barbara H. -
January 22, 2011
A:

THANKS. THAT INFORMATION WAS VERY HELPFUL. I WAS AFRAID MOST OF THE PARTS IF NOT ALL WERE DISCONTINUED. ORDERED CIRCUIT BREAKER AND WILL GO FROM THERE. THANKS AGAIN.

Read More
laura -
January 22, 2011
A:

Thank you for your question.

I see you have ordered a new breaker for the treadmill. If you need further assistance with the treadmill, I will be happy to help. Please reply with the details of the problem. Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
January 23, 2011
See more answers

Top Parts