Model #831296558 LIFESTYLER Treadmill

  • Unit Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Lifestyler Treadmill

A:

Thank you for taking the time and submitting your question, we will be glad to do verify if we will have a manual for you to down load for free. If you can please reply to the thread below with complete model number, I will happy to confirm if we will have a manual to down load. Thank you for choosing Manage My Life.com.

Read More
Maira -
Sears Technician
August 15, 2013
A:

Thanks for the reply. I'll respond with requested data in a couple of days. Just had surgery.

Read More
Mary -
August 15, 2013
A:

Manual for Artic Incline 2800 Model #831296558 Serial #217910 Thanks! Mary

Read More
Mary -
September 07, 2013
A:

Hi, Just a follow up to previous reply -- I'm looking for a manual on the Artic Incline 2800, Model #831296558, Serial Number 217910. Looking forward to your reply. Mary

Read More
Mary -
September 13, 2013
A:

Hello Mary. I am doing a follow up on the last request for a manual 831.296558. When looking for manuals they can be ordered on line at www.sears.com. Part number for the manual is 101971. There is a way to get it free of charge Mary. Just go to www.managemylife.com and then put in your model number and can download a new manual at that web site free of charge. If you have further questions please let me know. Thanks for choosing Sears PartsDirect.com

Read More
Larry L -
Sears Technician
September 17, 2013
See more answers
Q:

Wiring difference between treadmill motor control boards MC-20 and MC-60.

A:

I completely understand your need for some type of instructions or wiring diagram for your treadmill. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner.

Read More
Julio -
April 05, 2013
A:

Thank you for your question. I am sorry you are having a problem with the treadmill. The MC-60 motor control replaced most of the old motor controls. I will be happy to assist you with connecting the new control. The image below shows where the wires connect. Just click on the image to enlarge it. The three smaller wires connect on the left side of the control. The terminals are marked for the correct wire color. The red wire from the motor connects to the A+ terminal and the black connects to the A- terminal. The white wire left connects to the AC2 terminal and the black or blue wire left connects to the AC1 terminal. I hope this is helpful. Please let me know if you need further assistance. Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
April 08, 2013
A:

Mark, Thanks for the diagram. I connected the wires and the motor works! Unfortunately, I still have the same issue I was hoping the motor control board would fix. The motor turns, but when you step on the tread and try to walk the motor stalls and the tread stops. I've had the motor checked at a local motor shop and no issues were found. I did notice LED D11 is lit on the MC60 controller. Is is possible the motor brushes are in the wrong position? The motor company removed them to verify the brushes were not worn.

Read More
E -
April 08, 2013
A:

There are a few reasons your treadmill is slowing down or stop when you step on the belt. 1. If the walking belt or drive belt is too loose the treadmill will slow down when you walk on it, but it will not slow down if it is running with no load. That is because the belt is slipping. If you only adjusted the walking belt and not the drive belt, the drive belt could be slipping. To adjust the drive belt you will have to remove the motor hood. The drive belt is located between the motor and the front roller. To adjust the drive belt first, unplug the treadmill and remove the motor cover. Next, locate and loosen the motor mounting bolts. Then move the motor so that the belt is tight and have someone retighten the mounting bolts. It will take quite a bit of force to hold the belt tight. After the belt is tight plug the treadmill in and carefully test the operation. If the belt still slips, watch the front roller. If the roller stops but the pulley does not the roller is defective. If the roller and the pulley stop, the drive belt is still loose. As far as the walking belt goes, it should be adjusted to be able to lift it approximately 2 to 3 inches at either side of the middle of the belt. I have provided the instructions for adjusting the walking belt below. 2. If the walking belt slows down under a load and both belts are adjusted correctly the walking belt could be dry and in need of lubrication, especially if you have it in a garage. Having it in a garage is a not a good thing the dust and dirt get into the wax on the bottom of the walking belt and grind down the walking board surface causing drag. A dry walking belt is the most likely the problem. To correct this problem apply some deck wax, NOT Silicone, to the walking board. There is a lube kit available as well as a single tube. Both come with installation instructions, the part number for a single tube of wax is 219168 for $3.99, the part number for the kit which includes 3 tubes of wax,

Read More
Mark T -
Sears Technician
April 09, 2013
A:

an application wand and a case is 219170 for $29.99 and they are available at Sears parts direct Just in case the lube does not come with instructions, I will add them. Turn the walking belt until the belt seam is along the top of the front roller. Raise the belt on one side in the center of the walking board front to back as high as you can. Apply 1/2 the tube of lubrication to the walking board in a zig zag fashion moving from front to back. Move the belt until the seam comes up on top of the rear roller and lift the belt again and put the rest of the lubrication on the walking board in the same manner. Turn the treadmill on and walk on the belt for 10-20 minutes. Walk all over the belt to distribute the lubrication evenly on the walking belt and board. I hope this helps. If I can be of further assistance, please feel free to reply below. Thanks for using Manage My Life. Mark T.

Read More
Mark T -
Sears Technician
April 09, 2013
A:

Here is the image for adjusting the belt.

Read More
Mark T -
Sears Technician
April 09, 2013
A:

Mark, I verified the old motor control board was bad and lubed the walking belt. The tread mill works great now. Thanks for your help!

Read More
E -
April 14, 2013
A:

E, I am glad to hear your treadmill is working again. Please keep us in mind, if you have any other problems. Thank you for using Manage my life. Mark.

Read More
Mark T -
Sears Technician
April 15, 2013
See more answers
Q:

I am looking for an Electronic Monitor Guide that came with a Lifestyler 2800 treadmill model 831296558. Can you help?

A:

The Electronic Monitor Guide for this treadmill is no longer available.

The electronic monitor on your treadmill shouldn't need any adjustment to work. You set the speed with the knob on the monitor and adjust the height of incline manually.

If you have any questions about operation we can probably help you.

Read More
Jimmy K -
Sears Technician
March 03, 2009
A:

I just got this treadmill, used of course. It appears that I need a battery in the monitor section. Do you have directions on how to open that unit? The electric part of the treadmill and the incline works, as does the aqtomatic shutoff.

Read More
Judy -
September 05, 2011
See more answers

Top Parts