Model #831295051 PROFORM Treadmill

  • Walking Belt/motor/hood
    3 Results
  • Handrails/console
    3 Results
Find part by diagram >

Question and Answers

Q:

I have a Pro-Form XP542S Model #831.295051 and my incline is stuck on level 1...I tried calibrating it and it did not fix the problem.

A:

I can appreciate your wanting to resolve this issue so you can get back to using it right away.  I'm wondering if your unit might need to be recalibrated.   I have located a link that will discuss your situation in more detail. 
Click here to view the link.  Though this link discusses a different model number,
the mechanics are likely going to be very similar. Keep in mind that an expert will be
responding within the next two business days if not sooner and will likely offer you more information and
instruction. I hope this information will be helpful and have a nice day.

Read More
Henry -
July 23, 2013
A:

I understand how frustrating it can become when you experience an issue with your treadmill. I am happy to help with further information. Since the re-calibration did not work you could have a wiring failure between components. A failed incline motor, a bad console or a failed motor control board could prevent the incline system from working properly. The voltage diagram and calibration information for this treadmill are shown in the image below. This is the information that a technician would use to diagnose and repair an incline issue. If you are able to unplug the treadmill and safely access these components, you may be able to use the information below to check the wiring and the components.

If you do not find a wiring failure, you will likely need to conduct some live voltage checks to diagnose your problem. You should not perform these live voltage checks unless you are completely confident in your technical ability to safely conduct them.

If you are not sure about these type of checks, I highly recommend you schedule for a service appointment. Here is a link for the Sears Service website in case you need it: Sears Home Services .

Thank you for using Manage My Life.

Read More
Desiree -
Sears Technician
July 24, 2013
See more answers
Q:

I have a Pro-Form XP542s Treadmill. The incline function is not working.

A:

The treadmill may need calibrating. I am sending you some images with the calibration instructions for the treadmill.

If calibration doesn't help, there is probably a problem with the reed switch or the optic switch on the incline motor.

Without a model number, I can't tell if your treadmill has a reed switch or an optic switch and disc. If the console doesn't know where the deck is raised to, it won't turn on the incline motor.

Read More
Jimmy K -
Sears Technician
February 03, 2010
A:

The model number is: 831.295051

Read More
efp66 -
February 04, 2010
A:

I have this same model and my treadmill stops at level 1 on the incline. Everything else works. I tried calibrating it and that did not correct the problem. Thanks for your input.

Read More
Lisa -
July 23, 2013
See more answers
Q:

I need to replace the belt that is attached to the drive motor of my pro form xp 542s treadmill. Does anyone have directions to do this?

A:

Managemylife.com is a great place to find the answers to just about anything, especially on exercise equipment. I would suggest that you provide the model # of your product so your expert will be able to provide you the best possible answer. Share any insightful information that could be helpful. Continue this existing thread. Just click on the reply box below and provide that information.

Read More
aashe -
November 08, 2011
A:

Model # 831.295051

Read More
Lisa -
November 08, 2011
A:

Unplug the treadmill from the wall and then remove the motor hood. If you look at the motor you will see the screws that put tension on the belt. Loosen the motor up and remove the drive belt. Put the new drive belt in place and tighten the motor back up. The belt should have about 1/4inch movement when you push on it in the center between the motor and roller pulleys.

Thank you for using Manage My Life!

Read More
XX Wade_ -
Sears Technician
November 09, 2011
See more answers

Top Parts