Model #831246451 PROFORM Treadmill

  • Walking Belt
    3 Results
  • Hood/motor
    3 Results
  • Console
    3 Results
  • Uprights
    3 Results
Find part by diagram >

Question and Answers

Q:

Proform XP 580 Crosstrainer Treadmill

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner. Have a great day!

Read More
Alina -
January 12, 2013
A:

Before the start button is pushed, the red light is on in the controller. When the start button is pushed, the treadmill runs for about one second and then shuts off. The red light also shuts off during this time.

Read More
LuAnn -
January 13, 2013
A:

Thanks for contacting ManageMyLife.com. I understand how frustrating it is having trouble with the treadmill stop working. We are here to help. The common problem on treadmills is, the wires disconnect on the control boards. Just make sure each wire is plugged in tight. Most likely there is nothing wrong with the motor. The motor control board is the part that usually goes bad. A quick test for the motor is, run the treadmill until it quits. If the motor is bad, usually it would be burning hot. The dc motor rarely goes bad. The motor repair tech most likely is right. I recommend just replacing the motor control board. The part number is 248155. I hope this helps.

To order treadmill parts, please visit SearsPartsDirect.com with the model number.

Please feel free to let me know if you need further assistance. We are always here to help.

Thank you for using ManageMyLife.com.

Read More
John H -
Sears Technician
January 14, 2013
See more answers
Q:

Proform Model # 831.24645.1

A:

Calibration directions may have changed since the manual was created. I found the site for Proform that you may also be able to get answer. I Attached the link below. Hope this helps!

Read More
Barbara H. -
February 04, 2011
A:

Put the machine in calibration and have the motor hood off of the treadmill where you can see the board. When you get the machine to where there is an "85" in the distance display window of the console, check the speed. If it is anything above 10 mph the speed will need to be turned down on the controller board. There is a "speed pot" on the board. It should look like a little block with a screw in the middle of it. You will need to turn that back slowly until the speed reads 10MPH (or as close to that as you can get) on the console.

When you're doing this, make sure you do not touch anything else as the circuits are all live and will shock you. Make sure you only put the screw driver on the speed pot and not anything else on the board as a mistake can short the board or shock you. If you're not real sure about doing this procedure I recommend having a technician come out and adjust the new board.

Thank you for using Manage My Life!

Read More
XX Wade_ -
Sears Technician
February 06, 2011
See more answers
Q:

why wont my incline on treadmill wont go up and down

A:

I love to get a good workout and I know how important it is for you to have your treadmill working properly. While you are waiting for an expert answer, I did manage to find a link that will provide you with more information about your problem. I hope my link is useful.

Read More
Joseph P. -
December 13, 2010
A:

On the incline motor, there should be a little dish. That dictates to the controller what position the incline is in. My guess is that you took the old one off and put it on the new motor, which is fine. The problem is that the little disk just pushes onto the shaft. When it is removed from the old motor it makes the hole in the disk a very slight amount larger. The fix for this is to take the disk back off the motor, put a few drops of super glue on the shaft. Then put the disk back on and allow the glue to dry. Then it should be safe to calibrate the incline and your problem should be solved.

If that does not take care of your problem, let me know back on this thread and we can look into the situation a little further to try and determine the cause.

Thank you for using Manage My Life!

Read More
XX Wade_ -
Sears Technician
December 14, 2010
A:

I HAVE A PROFORM 580 MODEL NUMBER 831246451 AND MY INCLINE DONT GO UP AND DOWN ALL THE WAY I CHANGE THE MOTOR AND THAT DIDNT WORK I TRY CALIBRATE THE INCLINE and I put a new disk on to its still the same

Read More
JEFFP049 -
December 14, 2010
A:

With a new motor and disk, the only other thing it can be is a problem with the sensor (that reads the disk) or with the controller board. You may want to consider having a technician come look at the machine so you aren't putting more parts on it that it doesn't for sure need. The fact that it's moving at all makes me think there is a problem with the sensor though, normally a controller failure will result in no movement from the incline at all.

Read More
XX Wade_ -
Sears Technician
December 15, 2010
A:

THANK FOR YOUR HELP ANY WAYS

Read More
JEFFP049 -
December 15, 2010
See more answers

Top Parts