Model #8300 KENMORE Air Cleaner

  • Air Cleaner & Humidifier Filters
    3 Results
  • Air Cleaner & Humidifier Filters
    3 Results
Find part by diagram >

Question and Answers

Q:

What part number do I need? WFW8300SW00

A:

Water Temperature Sensor Error

If during the Wash Cycle in the water-heating step, the water temperature sensor (NTC) valve is out of range (-5 degrees Cto 103 degress C).
Note: To find correct Ohm reading refer to the Water temperature sensor section.

Possible Causes/Procedure
1. Unplug washer or disconnect power.
2. Check the water temperature sensor and connection to it.
3. Check resistance of heating element, if present on this model. (abnormal = infinity)
4. Refer to the Water temperature sensor section of manual.

Read More
Ernest7574 -
Sears Technician
November 23, 2015
Q:

My Duet dryer Has an Error Code F01

A:

A Washer is definitely something we depend on and when it begins to malfunction it can be a huge inconvenience. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question.

Read More
Priscilla V -
January 03, 2012
A:

I see Pvalde2 provided you with good information however, it does not pertain to a dryer. The F-01 error code indicates a primary control board failure on this model of dryer. If the error cleared after unplugging it for 20-30, then the control board could have received a power surge or glitch through the electrical lines. Completely disconnecting the electrical power and then reconnecting it will sometimes reset the board and it will operate properly. If your dryer continues to operate properly, then resetting the control board may have fixed your problem.

If the dryer motor continues to stop working, then you may have a bad control board. A wiring problem or drive motor failure could also prevent the dryer from continuing to run properly. A technician is normally needed to diagnose and repair this type of problem. If the F-01 returns and will not clear, then you will need to replace the control board in the dryer.

If you do not feel comfortable repairing the unit yourself, service can be scheduled at the following link: Sears Home Services . For further assistance, please respond to this thread with more detail. I hope this helps.

Read More
Korinna S -
Sears Technician
January 05, 2012
A:

Is it easy to replace the control board?

Read More
lisa -
September 17, 2012
A:

Please be sure to unplug the dryer prior to attempting any service or repair. I have included the instructions from the service manual that explain the process. Look it over and if you do not feel comfortable performing the task, service can be scheduled at the Sears Home Services link I provided above. For further assistance, please respond to this thread. I hope this helps.

Read More
Korinna S -
Sears Technician
September 18, 2012
A:

What would be part number for control board, where can I get one, and finially how much?

Read More
Sam -
November 14, 2012
A:

Hello Sam. WED9400SU is a partial model number that brings up 3 models. Two of the model have the same part number for the control board, while the other is different. Once you have the complete model number of your specific model, you can search for the part and purchase it from Sears PartsDirect. The diagram you want to be looking at is the "Dryer Cabinet" diagram. The control board you need is number 41 on the diagram. I really hope this information helps you today. For further assistance, please respond to this thread. I will be delighted to assist you. Thank you for using ManageMyLife.com

Read More
Korinna S -
Sears Technician
November 16, 2012
A:

I have a whirlpool duet sport gas model number WGD8300SW1, It started with F-1 error code, I checked control board and it had burn mark, so I changed it. the F-1 code is gone but I have NO heat. I take any help!

Read More
Sam -
November 24, 2012
A:

Hey there Korinna, the images you provided above are really small, can you please repost larger images?

Read More
clipper -
April 12, 2015
A:

i have a whirlpool duet dryer model number 4WED9200SQ1 i get an error message F1 what can i do myself to fix this please and thank u i put some clothes in it shut the door and it did start but then stopped and i heard a click sound then got the error i went to the fuse box and clicked it on and off and nothing it still wont work is there anyway i can do it myself at home appreciate any help u can give me thank u

Read More
denise -
May 25, 2015
A:

Hello, I have a Whirlpool dryer model Wgd8300sw1 that is giving me error code F-01. It does not clear when the unit is power cycled. Does the main control board need to be replaced, part number W10111606? Or what is the solution? Thank you.

Read More
Steven -
November 16, 2015
See more answers
Q:

WFW8300SW04 DUET SPORT WASHER - CCU REPLACEMENT NOT WORKING WFW8300SW04 Whirlpool Residential washer

A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you.

 
CONTROL BOARD REMOVAL OR REPLACEMENT

IMPORTANT: Electrostatic (static electricity) discharge may
cause damage to electronic control assemblies. 
NOTE: Be sure to perform the Diagnostic Tests before replacing the control board.
To remove Central Control Unit (CCU):
1. Unplug washer or disconnect power.
2. Remove all connectors from the CCU.
3. Place two flat blade screwdrivers under the left and right tab, on the top of the CCU and slide the CCU forward.
To reassemble CCU:
1. Align the tab on top of the CCU with the notch in the cabinet.
Also, align the posts on the back of the CCU with the hole in the back of the cabinet.
2. Slide the CCU back into place.
3. Reconnect wire harness.
To remove the touch-pad/LED assembly:
1. Unplug washer or disconnect power.
2. Disconnect touch-pad/LED assembly wire harness from the CCU.
3. Remove dispenser drawer.
4. Remove left front screw that was covered by the dispenser drawer.
5. Open door, under the center of the touch-pad/LED assembly there is a notch, insert a flat blade screwdriver in notch to release the bottom of the touch-pad/LED assembly.
6. On the right hand side behind the touch-pad/LED assembly, press tab to release right side of the touch-pad/LED assembly.
7. Gently pry up and release the top of the touch-pad/LED assembly. This should completely release the entire touch-pad/LED assembly.
To remove Motor Control Unit (MCU):
1. Unplug washer or disconnect power.
2. Remove wire harness cover and disconnect the wire harness from the MCU.
3. With a flat blade screwdriver, lift the front tab up and slide the MCU forward.
To remove line/ interference filter:
1. Unplug washer or disconnect power.
2. Disconnect the three connectors from the line filter and power cord.
3. Remove the two screws which secure the line filter to the top brace.

8571903 this is the electronic control you should have received to replace your damaged one. If you did receive this, then I recommend running through a diagnostic cycle to see if there is any faults with the new board. 

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
July 27, 2015

Top Parts