Model #8088 SEARS Moped

  • Crankcase
    3 Results
  • Piston And Crankshaft
    3 Results
  • Clutch
    3 Results
  • Gear Box
    3 Results
  • Air Cleaner
    3 Results
  • Carburetor
    3 Results
  • Exhaust
    3 Results
  • Magneto Generator
    3 Results
  • Frame Assembly
    3 Results
  • Kickstand
    3 Results
  • Fenders
    3 Results
  • Chainguard
    3 Results
  • Fuel Tank
    3 Results
  • Pedals, Crank, And Chain
    3 Results
  • Front Fork
    3 Results
  • Swing Arm And Shocks
    3 Results
  • Handlebar And Lever Assembly
    3 Results
  • Handlebar And Lever Assembly
    3 Results
  • Front Wheel
    3 Results
  • Rear Wheel
    3 Results
  • Headlight And Switches
    3 Results
  • Tail-stop-light
    3 Results
Find part by diagram >

Question and Answers

Q:

I need a key for my Craftsman Tool box - lock number 8088.

A:

Never mind. Finally sorted it out by getting the right person on Chat.

Read More
RICHARD -
May 31, 2015
A:

Thanks for the inquiry and for being a valued member.

You can have a key special ordered with the lock number and the model number of the tool box. You need to call 1-800-469-4663 with the information to have the key ordered. Outside of that, you would need to replace the lock set. 

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
June 01, 2015
See more answers
Q:

no power

A:

I can fully understand your concern regarding this issue. I did locate a link that will discuss your situation in greater detail. Though this link discusses a different model number, the mechanics are likely going to be very similar. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instruction. I hope this link will help guide you as to what might be wrong with your washer and have a nice day

Read More
Henry -
May 05, 2013
A:

Thank you for your question and I understand your concern.

Based on your symptom and details, the machine control is faulty. 

If you do not hear a faint click of a relay closing on the machine control board when the power cord is plugged into a working outlet, the machine control board is most likely faulty.

The machine control is part #285925 which can be ordered from Searspartsdirect.com. 

Be sure and disconnect the power cord from the power source before removing the top and replacing the machine control board. 

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

Read More
Joey S -
Sears Technician
May 07, 2013
A:

Hi Joey, really appreciate your reply. I am a little confused about which part you are referring to, is it the box at the rear top or do you mean the actual user interface at the front?

Read More
tobin -
May 10, 2013
A:

I called Sears yesterday early AM and the gal told me the part number was "bad",

Read More
tobin -
May 10, 2013
A:

...oops, I just looked at your link again and I see it is the box at the rear top but it is called the electronic control, not the main control box...duh.

Read More
tobin -
May 10, 2013
A:

Tobin: The machine control board is part# 285925 and it's a substitute for part # 8181900 and is also referred to or called a Microcomputer/Machine control or it could come up a Control Electronic.

Read More
Joey S -
Sears Technician
May 13, 2013
A:

Hi again Joey, I purchased the part and put it in, plugged it in, and alas there was power to the front. I immediately pushed the pause button twice and it seemed to be doing what it should but it hadf 2 minutes or the number 2 on it. The machine also started a short buzz at approx. 2 second intervals, I though this was "normal...perhaps incorrectly so. I pushed the pause button a third time to clear it and poof, no power again. Did i fry the new board?

Read More
tobin -
May 13, 2013
A:

Tobin: Try disconnecting the power cord from the power source and let it sit a minute and then reconnect the power cord and see if it will power up. Also listen for the faint click of a relay when you plug the unit in. You could have a faulty user interface causing the display to go dead. Also, make sure both hot and cold water supply valves are open too.

Read More
Joey S -
Sears Technician
May 13, 2013
A:

Joey, no click, it certainly did when I first put it in

Read More
tobin -
May 13, 2013
A:

I did not plug all of the wires in this time...should i have done so? i just plugged the power lines in.

Read More
tobin -
May 13, 2013
See more answers