Model #79099913800 KENMORE ELITE Free Standing, Electric

  • Backguard
    3 Results
  • Control Unit - Induction
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

E035 error continued 79099913800 Kenmore Elite Electric range

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your range. Upon researching model 79099913800;an element failure or short can cause the fuse to fail, also a power outage or electric storm can cause the fuse to fail.

 

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
July 30, 2015
A:

Carlos, thanks for your reply. Since just the large element was on at the time of the failure (and I believe the fuse that blew is for that circuit, I am certainly suspicious that the element failed. Unfortunately, a simple resistance measurement does not show any differences between the elements. Is there a more definitive test for the induction elements? We did loose our 220 V service a couple months prior due to an issue with our utility service, but the range worked fine for 2 months after that, so I doubt the power blip is the root cause. We are considering just throwing in the towel and buying a new range. Has Electrolux improved their design over the past 6 years or is a new unit likely to develop the same problems? Induction cooking is great, but not at the expense of a top dollar range every 6 years.

Read More
Gary -
August 09, 2015
See more answers
Q:

EO35, blown 20A PCB fuse 79099913800 Kenmore Elite Electric range

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your range is not working properly. 

I do apologize per the technical manual I am not seeing a F35 for a range. I do see error codes for F35 for a washer only.

Replacing the Induction Control Assembly – When
replacing the induction control assembly on the back of
the range, do not over-tighten the 4 screws that secure
the Control Assembly to the range or the screws that
secure the rear wire shield to the Control Assembly.
Over-tightening the screws can damage the plastic
housings holding the circuit boards.

On the wiring diagram I see there are two boards that control the right and left induction cooktops. I recommend having a service technician diagnose the unit because those boards lead to the main control board. 


Here is information to test the board: 

I do show 35 or 75 AC Input voltage too high.
1. Verify chassis ground wire connection to terminal X17 on filter board & to chassis ground.
2. Test for approximately 240 volts AC at filter board terminals X1 - X4 & X2 - X5.
3. If voltage is correct (240 volts AC ± 10%) replace filter board.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
July 28, 2015
Q:

Induction Range Controller unit - 790.99913801

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Alina F. -
December 29, 2011
A:

The Err indicates that you have an internal problem with that clock control board. The image below shows the technical explanation for that Err code. This indicates that the Err code is probably related to the display problem that you are having with that clock control board.

I recommend that you replace the clock control board with the part 5304474504. Here is a direct link for that part: Control Repair Kit .

Be sure that you unplug the range before accessing internal components and replacing that clock control board in the range. You should be able to access it by removing the upper back panel.

Once you replace that control, it should last for many years. That being said, the electromechanical control devices in that range can fail at any time. It is just not that likely. A power surge or glitch through the electrical lines (normally occurring during an electrical storm) can cause damage to the control board on that range.

If you are not confident that you can replace that clock control board yourself, then you can have it replaced by a Sears Technician. Here is a link for the Sears Service website where you can schedule service online: Sears Home Services .

If you need more help, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
December 30, 2011
See more answers

Top Parts