Model #79096322401 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Replacing oven base 79096322401 Kenmore Electric range

A:

Thank you for being Sears’ valued member and for contacting SearsPartsDirect.com with your question about your Kenmore range model 79096322401. I am so sorry aluminum foil has melted on the oven base panel. I will be happy to help you with how to replace the part. I have included the link below to order the panel, in case you haven’t done that yet.

SAFETY WARNING: Disconnect the power supply before beginning your repair to prevent the risk of electrical shock which can result in property damage, serious personal injury or even death. If you are not comfortable completing this repair, you can set up service at www.SearsHomeServices.com or by calling 1-800-469-4663 (1-800-4MY-HOME). 
 
Removing the base panel will be fairly easy. You will need to start by removing the two thumb screws at the back of the panel. Next you will need to pull the panel slightly back and up to release it from the front lip of the oven. You should then be able to remove the panel and replace it. 
 
I hope this answers your question. Thank you for choosing Sears, we appreciate your business. 
 

Read More
Rachel Morgan -
Sears Technician
May 11, 2015
Q:

How do I install my clock/timer electronic on my kenmore electric range?

A:

i completely understand your need for some type of instructions on how to properly install the new clock/timer on your range. I would suggest that you provide a little more information such as the make and complete model number of your product, so your expert will be able to provide you with the best possible answer. Just click on reply down below, where you can provide the additional information.

Read More
Julio -
April 08, 2013
A:

Kenmore Electric range Model 790.96322401, serial no. VF44677021. Thanks for the above reply.

Read More
Kristine -
April 09, 2013
A:

Thank you for your question and I understand your concern.

In order to access and replace the Electronic Oven Control/Clock assembly you will need to slide the range out from the wall and disconnect the power cord. 

Remove the screws and the cover from behind the control panel. You will see 4 screws securing the oven control. Remove the screw in each corner to remove the control. There is also a clock overlay covering the face of the control board. You may be able to peel the overlay from the old control and re-apply it to face of the new control. You may need to order a new overlay if it will not stick on the new control. Disconnect one wire at time from the old control and transfer the wire to the matching terminal on the new control. Reverse the procedure to complete the installation.

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

 

Read More
Joey S -
Sears Technician
April 10, 2013
See more answers
Q:

Oven light stays on for kenmore Electric range.

A:

A oven is definitely something we depend on and when it begins to malfunction it can be a huge inconvenience. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question.

Read More
Alina F. -
December 15, 2011
A:

Thank you for your question, on the oven light not going out with the oven door closed.

Yes! There was a service issue with the hinges not letting the door close enough to turn the light off.

It will require replacement of the oven door hinges.

The part number for the hinge kit is: 5304445529.

Here is the ordering information for replacing the hinges for the oven door below.

Hinge kit for oven door .

There are instructions in the kit that show how to replace the new hinge kit.

Please let me know how it goes.

Sam A.

Read More
Sam A -
Sears Technician
December 19, 2011
A:

Sam A -thank you for the answer. MY followup question is that is takes 18 minutes to preheat to 400 degrees. Is that normal? Also if I replaced the hinge kit to take care of the oven light problem would speed up the amount of time it takes to preheat? I am wondering if I am losing heat because of the faulty hinge door. Thanks

Read More
Dan -
February 10, 2012
A:

Thank you for the update. Yes it should also retain more heat in the oven but 18 minutes is about normal for a range to pre-heat to 400 degrees. Sam A.

Read More
Sam A -
Sears Technician
February 10, 2012
A:

hi, i have a Kenmore # 665.95775890 electric smooth top. i went to use the oven last night. instead of hitting the broiler button, to cook hamburgers, i hit the clean button, an the oven door was open. i tried hit broiler button and close the door, but by then the latch had moved to the right to lock the door, an the door wasn't closed.now i cant use the oven cause door wont close cause the latch wont move back to the left.it shows a code, E1-F5- an says to call for service, that the latch may need replacing,is there any way I can reset it on my own? i cant afford service right now

Read More
navyflipper -
March 12, 2012
A:

Hello Tim! I would suggest that you try this and let me know if it worked. Open the oven door and push and hold the oven light switch button all the while you program the oven to self clean. After programming the range to the self-clean cycle wait 30 seconds and the cancel the self clean cycle, still holding in the oven door light switch another 30 seconds. This will simulate the oven door being closed. This should get the latch hook back to the home position and the error code should go away. You should know be able to operate the range normally. Please let me know how it went. Sam A.

Read More
Sam A -
Sears Technician
March 13, 2012
A:

2nd posting,I didnt see my 1st post, so resending....Hello Sam A, I read ur advice. Went to the stove an hit the off/cancel button to reset back to the clock, like it was before, I pushed the oven light switch, an went to push the clean button an heard a grinding sound an looked down an the latch was moving back to its home position. So simple its stupid...i have my stove back..I have my own Plumbing Service, an give lots of advice to save them a Service call, I lose money, but I gain a happy customer an maybe future jobs. Im glad thats happened to me,for once. THANK again, Tim from TJ Plumbing Services in Co. If u have a Plumbing Question, Email me. I'll do my best to help You

Read More
navyflipper -
March 14, 2012
See more answers

Top Parts