Model #7909622340C KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

replacement vs substitute part

A:

I understand getting a substitute part that looks different from the original could be a concern. I have taken some time to research your question here on the Manage My Life website and I noticed that someone else had asked a similar question with a posted response from an expert. I attached the link below for you to view. I hope the link that I provided is helpful. Have a nice day!

Read More
Yadira B -
August 16, 2012
A:

That link for a previous answer that Yadira B. posted in the above response should help you with this problem. That terminal block replacement part is different than the original part but it is a manufacturer authorized substitution. It will work in the same manner as the original terminal block. You should have received 6 hex nuts and washers with the new terminal block. To install the new terminal block, you can unplug the range and follow these steps:

  1. Mark or note the wire locations on the original terminal block. Take a digital picture or make a drawing of those wiring connections if necessary.
  2. Remove the wires from the original terminal block.
  3. Remove the screws that secure the existing terminal block to the range.
  4. Mount the new terminal block.
  5. Secure the wires from the range on the terminal block posts with one set of the washers and hex nuts. Make sure that the wires are positioned properly according to your drawing or digital photograph.
  6. Position the wires from the outlet cord on the correct terminal block posts.
  7. Secure those wires with the second set of washers and hex nuts.
Here is a link for a previous answer that contains a brief repair video showing how to install that part: installation of terminal blk # 5304409888 and electrical cord on kenmore range #790.9611340A.

I hope that this information helps. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician install that terminal block, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
August 18, 2012
See more answers
Q:

Trying to order correct oven part

A:

It can be really frustrating dealing with a broken appliance. I did some research at managemylife.com and found an expert answer that i hope will assist you while you wait for your expert to respond. I attached the link below.

Read More
James -
December 08, 2010
A:

I'm sorry you are having this problem. The EOC (electronic control) for your range is # 316452310 and is available at SearsPartsDirect . I hope this will help you. If you would like more assistance, any additional details will be helpful. Thank you for using Manage My Life.

Read More
Scott D -
Sears Technician
December 09, 2010
See more answers
Q:

Broiler broken

A:

Having a broken broiler can be quite frustrating especially with the holiday around the corner. While you are waiting on an expert to answer your question, A suggestion I have is to visit Sears Home Services website to set service with a Sears technician. I attached the link below. Hope this helps!

Read More
Dezeray S -
November 30, 2010
A:

Thank you for your question and I understand your concern. I do not recommend using the Bake function with a blown out broil element. Using the Bake function could cause the electronic oven control to fail.

The broil element alternates operation with the Bake element during the Bake mode and it could cause damage to the electronic oven control board with the broil element still connected. There is a high possibility when the broil element burnt out and shorted it may have already damaged the electronic oven control board. If the broiler does not work after replacing the broil element and/or the bake element does not work after replacing the broil element, the control board will have to be replaced too.

Read More
Joey S -
Sears Technician
December 01, 2010
See more answers

Top Parts