Model #79096214406 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Electric range

A:

when it comes to working on removing parts on the range can be difficult. I have taken the time to research on the website and have located similar information towards your question. While you are waiting for a detailed reply from an expert I have attached the link below. Hope this helps!

Read More
Priscilla V -
March 26, 2012
A:

Be sure that you have the range unplugged when accessing internal components.

I assume that you already pulled the button off of the front of the console. If not, remove that button first. I believe that the button pulls straight off. Once you get that button off, remove the wires on the back of that simmer switch (with the range unplugged ). You should be able to then pull that black switch body out of the plastic clip. You may need to rotate or release a clip that holds it in place. I do not have a display range at our facility that we can use to determine exactly how to release that switch body. You will need to depend on your personal examination of the installed switch to determine how to remove it. If you need more help, reply with a photo of the switch and we will try to assist you further.

Read More
Lyle W -
Sears Technician
March 27, 2012
See more answers
Q:

my oven went out and clock, but burns are working? help thank you glen.

A:

I know how important it is to have a good working oven in the home so that you can bake a lot of great meals and I will be happy to help. While you are waiting for an expert answer, I did manage to find a link that will provide you with some good tips about what may be causing your problem. I hope my link is useful.

Read More
Joseph P. -
January 24, 2011
A:

I provided a wiring diagram in the image below that shows the voltage supply circuit to the control board in this range. The L1 hot wire is traced in red. This should be a black wire connected to the L1 spade on the control board. The neutral side of the power supply is traced in green. This should be a white wire. I recommend that you unplug the range and check these wiring connections on the control board. Remove the upper back panel to access the control board. Check the control board for damage or burned spots. If the board is damaged then it will need to be replaced. The part number of the control board is 316452310. You can order one from the Sears PartsDirect website. It costs around $100. Here is a direct link for that part: Clock timer .

If the wiring is okay and you see no damage or burned spots on the control board, then the normal troubleshooting procedure used by a technician is to check for proper voltage through the black L1 wire and the white neutral wire described above. I usually don't recommend that you check this live voltage yourself. If you are completely confident in your technical ability to safely check that voltage using a volt/ohm meter, then you can determine whether the control board is getting voltage. If it is getting voltage but will not power up then it will need to be replaced. A safer way to check the wiring (with the range still unplugged ) is to measure the resistance between the L1 connection on the terminal block and the black wire on the L1 connection of the control board. You would also need to check the white neutral wire connection on the control board to the neutral connection on the terminal block. You should measure near zero ohms of resistance through these wires. If you do, then you know that the control board is getting voltage since the burners still work.

If you find an open circuit during this test, then you will need to unplug the range and check the wiring between the terminal block and the control board.

This information should help you repair this range problem yourself. If you need more assistance, reply with additional details.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 25, 2011
See more answers

Top Parts