Model #79096119401 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Oven will not heat up, no errors, elements are fine 79096119401 Kenmore Electric range

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your range. Upon researching model 79096119401; since you have already tested the bake element, I recommend that you unplug the range power cord and remove the oven sensor when the oven is not hot. With the sensor removed you can test the sensor for continuity using a multi meter. The test reading should read continuity and it should read any were from 1000- 1100 ohms of resistance. If the test reads no continuity then the sensor may need to be replaced. In case the test shows the sensor to be ok, then the control board may need to be replaced. I have posted a link of the control board and the sensor below to view the parts click on the links.

Oven sensor link click here.

Electronic control board link click here.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
April 16, 2015
Q:

Oven Error when heating F10.

A:

Thank you for your question.  I am sorry for the problem with your Kenmore 790.96119401 Electric Range.    The F10 error indicates a runaway oven temperature.  This can mean the relay on the control board stuck in the closed position or it might indicate a problem with the temperature sensor.  Electronic control  boards are easy to buy but difficult to return if not needed.  My first suggestion to you is to try and recalibrate the oven temperature.   The instructions are in the image below.  Try this first and see if the F10 error repeats.  I hope this helps.  You can reply below with any additional details for further assistance.  Thank you for using Manage My Life. 

Read More
Fred M -
Sears Technician
October 01, 2013
Q:

Baking and broiler elements will turn on

A:

Title is wrong. I meant will not turn on.

Read More
cwfairlane -
October 31, 2012
A:

I am sorry that you are having some difficulties with your range and I will be happy to help. I did some research and I was able to find a link that will provide you with some good information. I am also adding a second link in where you can set service to have your range repaired by a certified technician. I hope this helps with your range troubles while you wait for your expert response.

Read More
Joseph P. -
October 31, 2012
A:

It's definitely an inconvenience when the oven will no longer work. I'm happy to help you today. I see Joseph provided you with some excellent information. Since the top elements are working fine, more than likely that you have a failed clock control board in the console. The popping noises that you heard were the relays on that control board shorting out. The display may still work but the relays are probably damaged.

If you are comfortable in doing so, You can probably fix this problem yourself by replacing that clock control board (part 316557118). You may also need the overlay (part 316419109) unless you can reuse the original one that is one the range. Before ordering that part, you can unplug the range and check the wiring on the control board.

  • Remove power to the range.
  • Pull the range out from its location and remove the upper back panel for the control area.
  • Locate the electronic oven control in the center of the control panel and remove the four screws to remove the control from the control panel.
  • Unlock the connector for the ribbon strip to the touch pad and carefully remove the strip from the old control.
  • With the new control in hand replace all the connectors one at a time until your have connectors off the old control onto the new control.
  • Carefully install the touch pad ribbon strip into the unlocked connection on the new control with bending any of the connections and then relock the ribbon connector.
  • Install the new control back into the control panel and restore the back panel to the range and check operation.

Parts can be ordered from Sears PartsDirect . These tips should help you resolve this range problem. If you need more assistance, reply with additional details. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

I really hope this information helps you today. Thank you for using ManageMyLife.com.

Read More
Korinna S -
Sears Technician
November 01, 2012
See more answers

Top Parts