Model #79096018502 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

Installed new bake element but won't work 790.96018502

A:

Thanks for your question- we see that no one from the community responded.  If you still require assistance on this topic, please resubmit your question with any updated information and we will have one of our experts take a look.  Also, we have updated our site to include information regarding common repairs and diagnosis, which can be found here: www.searspartsdirect.com/repair-help.html.  If you are looking for your owner’s manual, it can be found here: http://www.searspartsdirect.com/partsdirect/user-manuals.  Thanks for visiting SearsPartsDirect.com.

Read More
Sherman_G_Wallace -
Sears Technician
May 14, 2014
Q:

KENMORE STOVE 79096018502

A:

When things are not going right with the Kenmore range, managemylife.com is there to help. A similar question has been answered in the link that is attached below. Hope the this helps while waiting for a response from an expert on your specific model. If this is not a repair for you, I have attached the link for service also.

Read More
Anna T -
January 18, 2013
A:

You could have a voltage supply problem to the range that would cause that problem. Make sure that the range is plugged properly into the electrical outlet. You can unplug the range and check the wiring of the outlet cord on the terminal block as shown in the installation manual. Here is a link for the installation manual in case you need it: Installation Instructions . Check the outlet cord for damage. If you find no problems with those issues, then you can check to see if the surface burners work when the control for the oven shuts off. If the surface burners work when the electronic oven control shuts off then you probably have an internal wiring failure or bad electronic oven control board. You can unplug the range and check the wiring connections on the electronic control board. The wiring diagram in the image below shows the black L1 and the white Neutral wires on the control board that supply the voltage to that component. If those wires are connected properly and the control board is getting power when it blacks out, then that control board will need to be replaced. Note: Use extreme caution if you check the live voltage going to that control board through the black and white wires using a volt/ohm meter. Wear electrical safety gloves and safety goggles when checking live voltage. Unplug the range as soon as live testing is completed . You will need to check that voltage in the failure mode to accurately diagnose this failure. That may be difficult since this is an intermittent problem. If that control board is bad, then you can order a replacement from this page: Kenmore Range Model 790.96018502 Backguard Control Parts . The part number for the control board is 316557118. You will normally need to order and replace the overlay (part 316419109) at the same time that you replace the control board. Be sure that you unplug the range before accessing internal components and replacing parts.

I hope that this information helps. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 21, 2013
A:

Here is the image.

Read More
Lyle W -
Sears Technician
January 21, 2013
See more answers
Q:

Can I replace the electronic oven control in my range or should I have an electrician complete this repair?

A:

If you have the technical ability to safely access the electronic oven control board, you should be able to complete this repair yourself.

You can order a replacement control board from the SearsPartsDirect website www.searspartsdirect.com . The part number is 316418208.

Accessing this part involves unplugging the range and removing the upper back panel on the range. With this cover removed, you will see the oven control board. You can take a digital picture of the board to make sure that you can determine where the wires and plugs fit onto the new board. Disconnect the wires from the old board. Remove the screws that attach the old board to the console. Attach the new control board and reattach the wires on the new board. Reassemble and test the range.

If you need more help with this repair, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
October 31, 2008

Top Parts