Model #79096010401 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Can't find replacement part 79096010401 Kenmore Electric range

A:

Thank you for choosing SearsPartsDirect. I will be more than happy to assist you with your Kenmore range.

From the information you have provided above, after researching model number 790.96010401. I have located the heating element for the oven for you. The part number for it is 316075104. I have linked it on our website for you so you can get this ordered ASAP. Click here.

I hope you found this information useful. Again thank you for choosing Sears, we appreciate your business, have a great day.

Read More
Benny23 -
Sears Technician
February 19, 2015
Q:

Kenmore Range Model Range 790.96010401

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Jackie S -
October 17, 2011
A:

Thank you for your question on how to replace the oven bake element.

The first thing to do is remove all power to the range.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Open the oven door and remove the oven racks.

Then locate and remove the two screws that secure the oven bottom panel to the oven cavity.

Once you have these loose lift the panel from the back and when you get it up about 8 inches pull the panel back and up to remove the oven bottom from the front lip of the oven liner.

This should expose the oven element.

Locate and remove the two 1/4 inch hex head screws that secure the element to the oven cavity.

Pull the element forward until you can gain access to the wire terminals on the back of the bake element.

Remove the wires and install onto the new bake element, these should be 1/4 push on connectors and return the element to its location and secure with the two screws.

Re-install the oven bottom and restore the oven racks to there position in the oven and test operation. This Utube video may help you but keep in mind that you have a hidden bake element.

Utube video .

I hope this information will help.

Sam A.

Read More
Sam A -
Sears Technician
October 17, 2011
See more answers
Q:

replaced oven baking element and oven doesn't work

A:

I'm sorry that you are having some difficulties with your Kenmore Oven . Managemylife.com is a great web site to receive expert assistance to just about everything. I did some research for you at managemylife.com and found an expert answer to a similar question that may shed some light on this problem. I have attached the link below. If you would like to schedule service from a qualified technician, I have also attached a link to searshomeservices.com. I hope theses links will be helpful until your expert can respond.

Read More
James -
March 26, 2011
A:

Thank you for your question and I understand your concern.

Based on your symptom and details it sounds like a faulty oven control board. If the surface elements work then the most likely failure is the oven control board. During the pre-heat and during bake, both bake and broil element should alternate operation. If neither element is getting hot, the oven control board is likely faulty.

The oven control board is part #316557108 which can be ordered from Sears PartsDirect NOTE: Disconnect the power cord from the power source before removing and replacing the oven control board.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
March 28, 2011
See more answers

Top Parts