Model #79096009601 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

Installation directions part TS775 TS775 for Kenmore stove 790.96009601

A:

Thank you for choosing SearsPartsDirect.com. That is a great question! Here is a step by step to replace that element:

You need a 1/4 in nut driver.
Be sure range is unplugged.
Open oven door and remove oven rack(s).
There are two screws on each side of the element on the back oven wall. Remove those screws.
Carefully slide old element out to expose the wires on each end. Do not pull element too far.
Remove each spade terminal by sliding off.
Remove element. Do not pull wires.
Place new element inside. Connect the left side spade to the the terminal by sliding together. Same for the right side.
Push terminals back in and put the screws back in.
That should do it!

I hope this helps you! Have a great day!

Read More
Samantha A -
Sears Technician
February 04, 2014
Q:

Electric Stove Radiant Burner Does not Heat

A:

A range is definitely something we depend on and when it begins to malfunction it can be a huge inconvenience.  While you are waiting for an expert to respond, I have added a helpful link that may provide information to assist you with your question.

Read More
Yadira B -
June 16, 2013
A:

Thanks for contacting manage my life about your range/oven model 790.96009601; sorry you are having a problem, I will be glad to assist you. Based on your description the most likely problem is the element itself has failed. I have attached a wiring diagram of the top burners only for your convenience.  If you have a high quality volt/ohm meter you can test voltage out of the infinite switch terminals H1 and H2. With the switch set to high heat for the burner it should read 240 volts ac.  This would indicate power is being sent to the burner assembly and it should be getting hot unless there is a broken wire in the circuit, which you need to check for also.  _Always disconnect power supply before servicing the appliance and when testing live voltage be sure to wear proper safety equipment (gloves and eye protection) also be aware of sharp metals on product_If you determine the burner is bad here is a link to the Rt. Front Element. I hope this helps, if you need additional help reply with more details and I will be happy to respond.  If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.Ron H.

Read More
Ron H -
Sears Technician
June 18, 2013
See more answers
Q:

my burners won't shut off.

A:

I agree that this issue with the burners would be unnerving. I did locate a similar question for this model that may offer some answers while you wait for the expert response. If you would like to hand off the worry to a qualified technician to set this right, the Sears Home Services scheduler is below. I hope this information helps toward giving you some peace of mind.

Read More
Barbara H. -
June 03, 2012
A:

Thank you for your question and I understand your concern.

The symptom you describe is very unusual. Usually when a burner switch fails, it will not heat.

The surface burners control the operation and cycling of the radiant burners. If the radiant burners to not regulate, the burner(s) switches are faulty.

The burner switches can be accessed and replaced by removing the panel located behind the console. Remove the knob and the two screws to remove the burner switch. NOTE: Disconnect the power cord from the power source before removing the panel from behind the console.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
June 05, 2012
See more answers

Top Parts