Model #79095684302 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore electric Oven #79095684302, Oven and Broiler will not heat.

A:

The smells of baking going on in our kitchen always brings back memories. I think we all get a little frustrated when an appliance we depend on starts acting up on us. I'm sorry to hear that you are having some issues with your Kenmore electric oven. I did some research at Managemylife website and found an expert answer to a similar question that may help until your expert can respond. I have attached the link below so you can check it out. If you are thinking about scheduling service and have a qualified technician assist you, I have also attached the link to SearsHomeServices. I hope the links below will help you out.

Read More
James -
March 27, 2012
A:

Thank you for your question and I understand your concern.

Based on your symptom and details I suspect a faulty electronic oven control/clock assembly. Also, inspect the bake and broil elements for any signs of blistering or cracks. When an oven element burns out or shorts, it can take out the electronic oven control board. If the bake and broil elements are Okay, replacing the electronic oven control will most likely repair your range. The bake and broil elements can be disconnected and tested with an Ohm meter. I added a YouTube video showing how to test the bake and broil elements. If the bake and broil elements test Okay, you can order the electronic oven control part #316207511 for Kenmore model range 790.95684302 from Sears Parts Direct.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
March 27, 2012
See more answers
Q:

no power to bottom element of kenmore range model

A:

I know how important it is to have a good working range in the home so that you can cook a nice home meal and also bake a good diner meal. While you are waiting for an expert answer, I did manage to find a link that will provide you with some good troubleshooting tips. I hope my link is useful.

Read More
Joseph P. -
April 18, 2011
A:

Thank you for your question and I understand your concern.

I must assume when you state there is no power to the bottom (bake) element that you mean there is no voltage at the bake element. The bake element must have 220-240 voltage supply in order to heat. NOTE: I do not recommend checking and confirming voltage unless you have experience and feel safe and confident in doing so, otherwise I recommend calling a service technician to diagnose and repair your range.

If the surface elements and upper (broil) element works, the failure is most likely the oven control board or a burnt wire connection in the bake circuit.

If you mean the bottom (bake) element is not heating and you assume the there is no power (voltage) then it could have a burnt out bake element. The bake element can be removed and disconnected and tested for continuity using an ohm meter. I added a YouTube video showing how to test the bake element. You can also visually and physically check the bake element for any cracks, openings or blisters which will indicate a burnt out element. NOTE: Disconnect the power cord from the power source before checking the element for any blistering and before removing the bake element.

Read More
Joey S -
Sears Technician
April 20, 2011
See more answers
Q:

Why would both the broiler and bake elements in my electric Kenmore range give out? Is more than just the elements??

A:

You are right, diagnosing the cause is just as important as replacing parts. While you wait for the expert to review your range model, you can check a more general answer I found from a previous expert post. I attached the link below. Hope this helps you get to the root cause.

Read More
Barbara H. -
January 14, 2011
A:

Thank you for your question and I understand your concern. Based on your symptom and details, if both bake and broil elements failed at the same time, the Electronic Oven Control board has most likely failed and not the bake and broil elements. The oven control board has double line break relay that is common to both bake and broil element. When the relay fails, the bake and broil are no longer supplied with L2 (line two voltage).

The EOC will need to be removed and replaced. The EOC can be removed and replaced by removing the panel from behind the console. NOTE: Disconnect the range from the power source before removing the panel from behind the console.

The EOC is part #316207511 at the cost of approximately $168.00. You can order the EOC from Sears PartsDirect

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
January 15, 2011
See more answers

Top Parts