Model #79095662103 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Do I need to remove back of range when installing replacement broiler element for Kenmore Electric Range (79095662103)?

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Jackie S -
October 20, 2011
A:

I will be glad to help you replace this element on your range once you have the new element.

� There are two methods to changing this element.

One is from the oven cavity and the other is by gaining access to the back of the range. � Disconnect the power to the range and open the oven door. It will make it easier to replace this from the front of the oven if you remove the door from the body of the range. Refer to the owner�s manual on page 26. If you do not have the owner�s manual door removal instruction page, I have included a picture below for you. �*Locate and remove the two � inch hex head screws that secure the element to the back wall of the oven cavity.

�* Remove the four screws that mount the element support to the ceiling of the range.

�* At this point carefully pull the element towards you to remove and draw the element and power wires into the oven cavity far enough to get to the hex head screws that secure the wires to the element.

Remove these wires and connect to the new element. Be careful when disconnecting the wire that you hold the wire connector terminal when you are removing the screws so as not to damage or short out the connection. The same is true especially when installing the new element. Firmly tighten the screw connectors on the new element. And reinstall the element into the back of the oven liner and secure with their screws. � Re-install the element supports in the ceiling of the range that support the element.

� Re-install the door and return power to the range and test operation of broil element.

�* Note! In some cases when removing the element for the range from the oven cavity side the wires will not come through the liner. If this is the case you will have to access the wire terminals from the rear of the range by pulling the range out from the wall and removing the back panel. The rest of the steps are the same as above.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: www.searshomeservices.com?MML=MMLxexpertxmerch

Read More
Jerome G. - Personal Solutions Manager -
Sears Technician
October 20, 2011
A:

Excellent information, Jerome! Worked perfectly. Thank You. Keith

Read More
KEITH -
October 20, 2011
See more answers
Q:

I have a Kenmore oven model 79095662103 the door lock light is flashing and the oven will not work. (the door is not locked either)

A:

When an oven has an error code it can definitely be frustrating. I came across a great link that may be able to assist you. I have attached the link below. I hope this helps! http://www.managemylife.com/mmh/questions/133983-why-is-the-oven-light-staying-on-the-door-will-not-lock-on-my-kenmore-range

Read More
Alina F. -
October 28, 2010
A:

The door lock light is flashing because the control detects that it is in the process of locking or unlocking. You can try to reset it by pressing and holding the OFF/CANCEL key for 3 deliberate seconds with the oven door shut.

If that does not work, then you likely have a problem with the door lock assembly or the electronic control board in the oven. A problem with the door switch that controls the oven high can also cause this problem.

A service technician will normally need to diagnose and repair this type of failure. Here is a link for the Sears Service website: Sears Home Services .

If you are advanced in technical skills and want to fix this problem yourself, you can use the information shown in the image below to check the wiring connections on the control board and the door lock assembly. Unplug the range before accessing internal components. You can remove the back panels to access the control board and the door lock assembly. If the wiring connections are okay, then the door lock assembly may need to be replaced. Reply with additional details if you need more help diagnosing this failure.

Read More
Lyle W -
Sears Technician
October 29, 2010
See more answers
Q:

What is wrong with my Kenmore stove model #790.95662103 with error code F9?

A:

This code indicates a problem with the motor door latch assembly. If it's making a clicking noise, it indicates the motor apparently has voltage to it. You can try pressing clear and working the door back and forth at the same time. If it's jammed, this may free it. If it still won't open, the motor latch located behind the range (# 89 in picture) will need to be checked. To access the motor, the range will need to be pulled out and the back panel removed. First disconnect power to the range. Sometimes by removing the 2 screws holding the motor, it will also enable you to free the rod connected to it. If you can get the rod free and work it back and forth it may unlock the door but if the cam on the motor assembly is still in the lock position, nothing will work. In this case the motor assembly # 316137500 will need to be replaced. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Safety Notice: Be sure to disconnect the appliance before performing any troubleshooting procedures. If you are not comfortable with doing any voltage checks or repairs that might be recommended, please contact a local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Scott D -
Sears Technician
April 15, 2010

Top Parts