Model #79095661100 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

self cleaning oven won't start what's wrong

A:

I know that it can be very frustrating to have issues with your range. There are a few more steps to programming the self clean cycle, which are located on page 18 of your owner's manual. Since you do not have one, just click on this link to download and print it: Owner's Manual. If the self clean cycle is still not working, then you most likely have an issue with the control board. This will require testing to determine if it is the problem. I hope this helps. Please feel free to let me know if you need further assistance. We are always here to help. Thank you for using Manage My Life.com.

Read More
AnneJ -
Sears Technician
October 27, 2013
Q:

Oven not maintaining consistant cooking temp. 79095661100 Kenmore Electric range

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Dezeray S -
June 04, 2013
A:

You could  be experiencing an issue with the main control board or the oven sensor temperature probe. I recommend testing the temperatue probe first. Disconnect the sensor plug (image one) and then insert one meter lead into the terminal of the temperature probe plug and place the other meter lead into the other terminal of temperature probe plug. Place the dial on your multimeter to 200K (image two). The temperature probe should measure 1091 ohms plus or minus 5.3 ohms at room temperature of 75 degrees plus or minus 2.5 degrees, if it's okay. If it does not measure approximately 1091 ohms, replace the temperature probe (316233902). If the oven temperature sensor has approximately 1091 ohms, then the oven control board (316207522) will most likely need to be removed and replaced. You can order parts from our Sears Parts Direct web site. I hope this helps. Please reply back to this thread if you require further assistance. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
June 05, 2013
A:

Is the most efficient / direct access to the temperature probe through the back of the oven. Thank You!

Read More
Robert J Muenzner Jr -
June 07, 2013
A:

Is the most efficient / direct access to the temperature probe through the back of the oven. Thank You!

Read More
Robert J Muenzner Jr -
June 07, 2013
A:

Robert, sometimes you'll able to unscrew the probe fom the interiro cavity and then full it forward and disconnect it from the harness for replacement. If you're unable to access the harness that way to disconnect it, then you'll need to pull the unit out and take off the back panel in order to disconnect the probe. I hope this helps. Please let me know if I can assist you further.

Read More
Tykara -
Sears Technician
June 07, 2013
See more answers
Q:

What can I do about my oven not turning off?

A:

The oven not turning off sounds dangerous and I will be happy to help. I did some research and I was able to find a link that will provide you with some good information. I am also adding a second link in where you can set service to have a certified technician fix your range. I hope this helps with your range troubles while you wait for your expert response.

Read More
Joseph P. -
October 31, 2012
A:

Thank you for your question and I understand your concern.

There are a couple things that can fail and cause the bake or broil element to stay on. If the bake or broil element happens to burn out and short to ground, the element will remain on. If the bake or broil element is not shorted, the electronic oven control/clock assembly is faulty and it will need to be replaced. The bake and broil elements can be accessed from the rear and tested with an Ohm meter to see if one is shorted to ground. NOTE: Disconnect the power cord from the power source before removing the rear panel. Disconnect the wires from the bake and broil elements before testing each element. When testing the elements, place one Ohm meter lead on the terminal and the other meter lead to the heating element casing. It should not measure any continuity or resistance.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
November 02, 2012
See more answers

Top Parts