Model #79095423301 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

kenmore electric range cooktop working but broil and bake do not 79095423301 Kenmore Electric range

A:

Thank you for the inquiry and for using SearsPartsDirect.com. I am sorry to hear of the oven cavity heat issue you experienced after the self-clean cycle, I know how frustrating it is to not have the oven operational. 

So, just to clarify, does the oven still heat to 100 degrees, or is there no heat at this point? If the oven cavity is still heating to 100 degrees or so, it very well could be the oven temp probe sensor, however, if there is absolutely no heat at this point from either bake or broil, it sounds like a communication error between the board and the oven, and usually the board will need to be replaced in that case.

If you would like to test the probe for resistance, I have included a document below that you may click on to get the resistance ratings. You will need to have a multimeter to check the probe. The probe more or less regulates oven temp, whereas the board supplies the oven with the power to heat.

If you are viewing this response on SearsPartsDirect.com, click here to view this response on ManageMyLife.com with attachments.  

Depending on your check of the probe, you can also check the electrical Pins on the board that supply power to the oven to see if any power is coming from the board. There should be an electrical diagram on the oven to reference. If not, I have also enclosed a diagram that shows which Pins to check. 

Depending on which part you deem is at fault, I have included blue links below that you may click on to be directed to the PartsDirect page to view and purchase the part. If you need a replacement board, you will also want to replace the overlay.

Electronic Control for Model 79095423301

Electronic Control Overlay for Model 79095423301 

Oven Temp Probe Sensor for Model 79095423301

If you have any further inquiries, please don't hesitate to ask. Thanks for using SearsPartsDirect.com.  

Read More
Jeff Wallace Sr -
Sears Technician
September 12, 2013
Q:

Kenmore electric range model 790.95423301

A:

Error codes can be a hassle and keep your range from working properly. I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided assistance for you.

Read More
Joseph -
January 03, 2012
A:

You can try to reset the control board by completely unplugging the range to disconnect electrical power. Leave it unplugged for 3 minutes. Plug it back in and see if you can set the clock and use the control normally.

If the F1 returns then you have a component failure.

That F1 code on your range indicates that you one of the failures shown in the image below. There is a possibility that you have a bad oven temperature sensor probe or a failed clock control board. I recommend that you check the oven temperature sensor probe using a volt/ohm meter. Here is a brief repair video that shows how to test that component: Oven Sensor Testing . Here is a video that shows how to access that sensor probe: Oven Sensor Replacement . Unplug the range before accessing internal components. You should measure around 1086 ohms of resistance (+/1 50 ohms) through the sensor probe. If that sensor is bad, it will need to be replaced. You can order that part online from the Sears PartsDirect website. The part number for that sensor probe is 316233902.

If the sensor is okay, you will probably need to replace that clock control board in the console of the range. The part number for that clock control board is 316207511. Here is a link for a video that shows how to replace that clock control board: Range Clock Control Replacement . Unplug the range before beginning that repair. You may need to order the overlay for that clock control unless you can reuse the original one as shown in that repair video.

If you need more help, reply with additional details.

If you get to a point where you need to have a service technician examine the refrigerator and fix this problem, you can schedule one through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 05, 2012
See more answers
Q:

Why did the oven "pop" and go off with the oven door locked after setting it to self clean?

A:

According to your description, it is possible that the electronic oven control board may have been what "popped" when you set the self clean cycle. Check the electrical breakers for the range. If they are tripped you can reset them. Carefully plug the range back in. If the breakers trip immediately, I recommend unplugging the range and calling a service technician to diagnose and repair the failure.

If the range is plugged in and the control will not power up or respond when you attempt to cancel the self clean cycle, then it is likely that the electronic oven control board will need to be replaced. I recommend calling a service technician to complete this type of repair.

Read More
Lyle W -
Sears Technician

Top Parts