Model #79095411100 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Door
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Why won't my oven realize it is done self cleaning?

A:

Thank you for your question and I understand your concern.

Based on your symptom and details, it could have one of two possible failures. It could have faulty electronic oven control/clock assembly or the oven temperature sensor could be faulty.

If you unplug the range and let completely cool and then reapply power and it begins heating without touching the controls, the electronic oven control is faulty and will need to be replaced.

The oven temperature sensor probe is located inside the oven cavity. The temperature sensor is mounted on the back wall in the upper left corner or possible upper right corner. If you do not see any screws securing the oven temperature sensor from inside the oven, then you will have to access and remove the sensor from behind the range. You will likely have to remove the rear panel to access the sensor. NOTE: Disconnect the power cord from the power source before servicing. The temperature sensor probe can be removed and tested with an Ohm meter for proper Ohm resistance. At room temperature, the oven sensor should measure approximately 1100 Ohms of resistance. If it does, then the electronic oven control/clock assembly is faulty and will need to be replaced. If you do have to replace the electronic oven control/clock assembly, there is clock face plate you will need to peel off from the old clock and stick in on the new clock. If it does not stick well, you will need to order the clock overlay. You can look up and order parts for your Kenmore range model 790.95411100 at Searspartsdirect.com

The clock/oven control is an easy procedure to replace. Remove the cover from behind the control panel to access the screws securing the clock/oven control. Disconnect one wire at a time from the faulty clock and re-connect to the same terminal on the new clock. 

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

 If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link:Sears Home Services.

 

Read More
Joey S -
Sears Technician
September 27, 2013
Q:

What does error code "F1" mean?

A:

The "F1" fault code generally implies an oven control failure. It either has a shorted keypad, a corrupted checksum or it sensed a runaway oven condition. It could have a shorted relay or the RTD sensor may have gone bad. I recommend removing the oven temperature sensor probe from inside the oven cavity and test it using an OHM meter. The oven sensor probe should have a resistance measurement of 1091 ohms plus or minus 5.3 ohms at room temperature of 75 degrees plus or minus 2.5 degrees if it's okay. Then oven sensor probe is located attached to the rear panel inside the oven cavity in the upper left hand corner or possible in the upper right hand corner. Remove the two screws and slide it out and then disconnect the harness plug and test the resistance of the sensor. If the sensor is okay, replace the oven control. NOTE: Disconnect the range from the power supply before replacing the oven control. The oven control is part #316207502R at $140.99 and the oven temperature sensor is part #316233902 at $9.87. [ Sears Parts Direct |http://www.searspartsdirect.com/partsdirect/showPart.pd?partNumber=316207502R&productGroupId=0022&supplierId=628&pathTaken=partSearch&filterPart=&pop=flush

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
April 15, 2010
A:

I just don't understand why there is no beeping or problem when I am using the oven, only when it is off? So I just flip the breaker to stop the beeping.

Read More
Sandra -
March 21, 2012
A:

Sandra: Your range/oven could have an issue with the touch pad causing the random beeping. I know it does not make a lot sense; but it's likely caused by the touch panel. If the buttons or key switches are shorting out at times it can cause the random beeps.

Read More
Joey S -
Sears Technician
April 20, 2012
See more answers
Q:

Oven stays on???

A:

A non working Oven is not something any of us want to see. If you are technically handy, this is a good site to get instruction and fix some things yourself. If you do not feel confident doing your own repairs, an option is to visit Sears Home Services and use the scheduler. While you wait for the expert to review your model, you can check the bottom links for some possibilities. Hope this is of help.

Read More
Priscilla V -
January 23, 2012
A:

This type of failure is normally caused by a failed relay on the clock control board in the console of the range. That component will probably need to be replaced to fix this problem. You can order that clock control board from the Sears PartsDirect website. Here is a brief repair video that shows how to replace the clock control board in a typical range that displays that F1 error code: Range Clock Control Replacement . Be sure that you unplug the range before accessing and replacing internal components.

This information may help you repair this failure in your range. Reply with additional details and the full model number of your range if you need more assistance.

If you want to have a service technician repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 24, 2012
A:

I looked on the Sears Parts Direct website and I saw a part 316222902... There wasn't any clock control board. The model number is 790.95411100. Does this help?

Read More
Andy -
January 30, 2012
A:

Thanks for adding that model number. The part 316222902 is the clock control board (also called clock/timer). Replacing that component as shown in that video will likely fix your problem. You may also need to order the overlay unless you can reuse the original one as shown in that repair video that I provided in the above response. Be sure that you UNPLUG the range before accessing and replacing internal components. If you need more help, let us know.

Read More
Lyle W -
Sears Technician
January 31, 2012
See more answers

Top Parts