Model #79095373804 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

i need a wiring diagram for kenmore electric stove #79059373804

A:

I know how useful the wiring diagram can be when doing some major repairs. I suggest you add to the thread of this question and include the full and correct model number of your range so that the expert can provide you with a more detailed answer. I am adding a link below to help you locate the model number. The expert can provide you with more detailed information about your range and he or she will respond within 24 to 48 hours. I hope this helps while you wait for your expert response.

Read More
Joseph P. -
April 17, 2012
A:

I provided the wiring diagram and a wiring schematic for that range in the images below. NOTE: That information is intended for technicians. Follow electrical safety guidelines when using that data. Unplug the range before accessing internal components .

If you need more help, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
April 18, 2012
See more answers
Q:

79095373804

A:

Wiring diagrams are important to have, especially on the Kenmore range. Below is a link to searspartsdirect.com where you may find that diagram. The experts will be with you shortly if the wiring diagram is found on line. Thanks for your patience.

Read More
Anna T -
April 17, 2012
A:

I provided the wiring diagram and a wiring schematic for that range in the images below. NOTE: That information is intended for technicians. Follow electrical safety guidelines when using that data. Unplug the range before accessing internal components .

If you need more help, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
April 18, 2012
See more answers
Q:

Kenmore Electric Range not heating properly

A:

An oven is definitely something we depend on and when it begins to malfunction it can be a huge inconvenience. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question.

Read More
aashe -
November 29, 2011
A:

I have the above referenced manual, but it doesn't tell me whether the oven's top element is supposed to come on when on BAKE. I know the top element is good because on BROIL it gets red hot fast.

Read More
Carl -
November 29, 2011
A:

The first image below shows a relay chart for that oven control and a wiring diagram. The broil element will alternate with the bake element in the bake and convection bake modes. I do not have the exact programming for that model that indicates when or how long that broil element is energized during that bake mode. When it is on, it is usually only for a very short time to promote browning. It is not used as a significant heat source in that bake mode. Your failure is likely in the bake element, the oven temperature sensor probe or the oven clock control board. I recommend that you unplug the range and check the resistance of the oven temperature sensor probe first. Here is a brief repair video that shows how to check that component using a volt/ohm meter: Oven Sensor Testing . Here is a link for a video that shows how to access that sensor in this type of range: Oven Sensor Replacement . Be sure that you unplug the range before accessing internal components. The resistance of the sensor probe should be around 1091 ohms at room temperature (75 degrees). If that sensor is bad, it will need to be replaced. You can order that part from the Sears PartsDirect website. The part number is 316490000.

If that sensor is okay, you can plug the probe back into the wire harness and check the resistance of the entire sensor circuit from the clock control board. Here is a link that shows how to access that component (with the range still unplugged from the electrical outlet ): Range Clock Control Replacement . You don't have to remove that clock control board yet. Just unplug the connector with the sensor wires (violet wires) and measure the resistance through that circuit. You should measure the same resistance as the sensor (1091 ohms at room temperature). If the resistance through that circuit is high, then you have a problem with the wiring harness. The disconnect plug at the sensor is the most suspect component in that harness. You may need to cut that disconnect plug out of the circuit and properly connect those sensor wires using ceramic wire nuts. You can get those ceramic wire nuts at you local hardware store or electrical supply outlet.

If you find not problems with that sensor circuit, you can check the resistance through that bake element circuit from the control board. Unplug the yellow wire on the BK (BAKE) spade (with the range still unplugged ) and check the resistance through the yellow and orange (L2 OUT) wires. You should measure around 16 ohms of resistance through that circuit (between 15 and 25 ohms). If you do not measure the proper resistance through that circuit, you can check the resistance of that hidden bake element directly at that component (with the range still unplugged ). Remove the bottom oven panel to access that bake element. You can remove it as shown in this video: Bake Element Replacement . If the resistance of that bake element is okay but the resistance measured from the clock control board is high, then you have a problem with the wire harness. If the resistance of that bake element is not around 16 ohms (15 to 25 ohms) then you will probably need to replace that bake element.

If the element circuit and the sensor circuit are both okay, then you will probably need to replace that clock control board.

These tips should help you fix this oven heating problem in your range. If you need more assistance, reply with additional details.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
December 01, 2011
A:

To Lyle W: Thank you, thank you, thank you!!! Although I have not tried any of this yet, I will soon, and what you tell me makes absolute sense. I am a retired engineer and very familiar with VOMs and testing, so the videos and your resistance figures will guide me to finding out what's wrong with my range. If I don't solve it, I will be back, but I really do appreciate you.

Read More
Carl -
December 01, 2011
A:

Thanks for the feedback. Don't hesitate to reply with more details if you need additional assistance.

Read More
Lyle W -
Sears Technician
December 01, 2011
See more answers

Top Parts