Model #79095322301 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

oven wont heat 79095322301 Kenmore Electric range

A:

I can understand how important it is to have the right information for you oven. By switching the L2 In and L2 Out, all you are doing is changing how the power comes in and out of the board. Since the unit is heating, I would suggest replacing the control board. These connections are not designed to route the power this way. It will work like this, but I wouldn't recommend it. I hope this helps. Please feel free to let me know if you need further assistance. We are always here to help. Thank you for using Manage My Life.com.

Read More
AnneJ -
Sears Technician
October 22, 2013
Q:

my kenmore electric range 79095322301 won't heat. model . broil doesnot heat either. everything else works.

A:

Thank you for your question. I know it's frustrating when the oven stops working. When both the bake and broil elements stop working at the same time, the most likely problem will be with the control. However, it could also be a wiring problem but it's not as likely. A good quick check will be to disconnect the power for 30 seconds and then reconnect it. This resets the control. If the oven works now, it may be all that will be required but if it stops heating again, the control would need to be replaced. If it still won't work, the wires can be checked by pulling the range out and removing the back panel. Be sure to disconnect the power first. With the panel removed you will be able see the wires connected to the elements. If the wires are ok, another check that can be made will be to, remove the back control panel cover, with the power still disconnected. Now, remove the wires from the terminals on L2 in and L2 out and connect the wires together. Make sure they don't touch anything and reconnect the power. Set the control to either bake or broil and if the element heats, the control # 316207511 will need to be replaced. It's available at Sears PartsDirect. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services.  

Read More
Scott D -
Sears Technician
September 23, 2013
A:

I CONNECTED L2 IN AND OUT AND THE ELEMENTS HEATED. WHAT WOULD BE THE RESULT OF USING THE OVEN THIS WAY THANKS FOR YOUR HELP

Read More
nomosno -
October 19, 2013
A:

Nomosno, this check is only to test and determine for sure the control has failed. It's not intended to be left wired in this manner. This would leave one side of the elements constantly wired to live voltage and by-pass the control. This is modifying the unit, which is definitely not recommended and could be a potential hazard.

Read More
Scott D -
Sears Technician
October 21, 2013
See more answers
Q:

Oven control beeps and displays F1 or F3

A:

Having a properly working oven is important. The error codes can be frustrating sometimes. I found some information for you that I am hoping will be able to help you. Please click here:[F1 and F3 error code]. Your expert will also help answer your question. It may take two business days for your expert to reply. I do hope that everything works out.

Read More
Marc -
July 16, 2013
A:

Thank you for choosing ManageMyLife.com. I understand how important it is to have a properly working oven. The error code F1 that you've provided indicates that your oven control has malfunctioned. Reprogramming the control board requires you to unplug the unit for several minutes and plug back in and you have done so already but the problem was not fixed. The F3 code is for a sensor probe failure. If you have a multimeter, you can test the oven control by following the instructions below.
SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

1. Attempt to preheat the oven to determine if the bake element is functioning. Turn off the oven after it has heated or if the oven does not heat at all after several minutes.

2. Select the "Broil" button on the electronic oven control to turn on the broiler. Wait several minutes for the element to heat to determine if the broil element is functioning then turn off the broiler.

3. Turn off the range's breaker in your household service panel to avoid injury or death while servicing the range.

4. Open the oven door and remove the non-functioning heating element if one element is working and the other is not. To remove the element, pull out the oven racks then remove the screws at the base of the element that secure it to the rear wall of the oven, along with the screws that secure it to the roof of the oven if you're removing the broil element. Pull the element away from the wall and pull the wires off of the terminals.

5. Test the element for continuity with a multimeter. Set the multimeter to the lowest setting to measure Ohms of resistance then calibrate the meter per the owner's manual. Touch one of the meter probes to one of the terminals on the heating element and touch the other probe to the other terminal. If the display shows 0 to 50 Ohms of resistance, the element is properly functioning; otherwise, it needs to be replaced.

6. Remove the oven sensor and test it for continuity. To remove the oven sensor, pull the range away from the wall then remove the rear panel. Disconnect the oven sensor connector then test it with the multimeter in the same manner that you tested the element. If the meter shows a reading of 1,000 to 1,100 Ohms of resistance, the sensor is properly functioning. If the meter displays a different level of resistance or an infinite number of Ohms of resistance, replace the sensor.

7. Replace the electronic oven control if both heating elements and the oven sensor has continuity but the oven will not heat.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services
I have included a link to our PartsDirect page where you can purchase the parts you may need to complete your repair. Just click the blue link below to be taken to the page.
Electronic Clock Control for Kenmore Range Model # 79095322301
White Overlay for Kenmore Range Model # 79095322301
If you would like more assistance, reply to this thread and I will be glad to assist you further. Thanks for using ManageMyLife.com.

Read More
Desirea -
Sears Technician
July 16, 2013
A:

Desirea, thank you for your response. Both the bake and broil elements work fine, so I am thinking it may be the oven sensor and I will test it as you descibed. However, I am wondering how much the replacement part will cost. When I went to the link you provided for parts and did a search for "oven sensor" or "sensor", there were no matches. Can you provide me with the part number for this part?

Read More
Nancy -
July 17, 2013
A:

Sorry for the delayed response I was able to locate the Temperature Sensor. I have included a link below to our PartsDirect webpage.

Temperature Probe for Model 790.95322301

If you have further questions please let me know.

Read More
Desirea -
Sears Technician
July 18, 2013
A:

Desirea, thank you for the additional info regarding the temperature probe. I have tested both heating elements and they are functioning fine. I have yet to pull the oven out from the wall to test the temperature probe but I will do it. In the meantime, I cut the power to the oven at night so as not to be awakened by the beeping sounds. When responding, it would be helpful if you would refer to the specific parts by their proper name. No where in your email did the words "temperature probe" appear. You referred to the part as "oven sensor" and consequently, I spent about 30 minutes looking at the available parts for my oven and came up empty as there is no part with that name. That in turn caused me to have to write again and for you to write back to me as well. It would save time for everyone.

Read More
Nancy -
July 25, 2013
A:

I completely understand, sorry for the confusion.

Read More
Desirea -
Sears Technician
July 26, 2013
See more answers

Top Parts