Model #79095320301 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

What does "F1" fault code indicate?

A:

The "F1" fault code is indicating a shorted keypad, electronic oven control board failure or the oven sensor probe (RTD) may have gone bad. I added a couple of images with the likely cause and the suggested corrective action. A technician would follow the suggested corrective procedure to determine which component has failed. It will either have a bad oven sensor probe (RTD) or a failed Electronic Oven Control (EOC) board.

I recommend calling a service technician to diagnose which component has failed.

Read More
Joey S -
Sears Technician
March 16, 2009
A:

We had a water line to break under our sink and the kitchen was flooded the stove was beeping and the the code on the display was showing F1 and are afraid it has shorted out. It was a couple inches of water under the stove.

Read More
KATHY -
September 16, 2012
See more answers
Q:

Kenmore oven and broiler not heating; everything else works fine.

A:

Homemade food and fresh baked good are great. The oven not being able to bake or broil can be most concerning. I found some information for you that I am really hoping will assist you. I am adding the links below to help you with your question while you wait for your expert response. I do hope this will help you with the oven.

Read More
Marc H -
April 29, 2012
A:

Thank you for your question and I understand your concern.

Based on your symptom and details I suspect a faulty electronic oven control (EOC). If the bake and broil elements are not getting 220-240 volts when measuring across the element leads, replace the electronic oven control. When measuring voltage from the control board leave one meter lead on the terminal labeled L2 out while placing the other meter lead on Broil or Bake. Be sure to have the oven started for bake or broil when measuring across the L2 out terminal and BK or between L2 out and BRL.

The electronic oven control #316207511 for Kenmore range model 790.95320301 can be ordered from Sears Parts Direct. NOTE: Be sure to disconnect the range from the power supply before removing the panel from behind the console assembly. The oven control is fastened by 4 screws located in each corner. Make a note of where the wires are connected before disconnecting the wires from the oven control board.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
April 30, 2012
See more answers
Q:

oven not heating up

A:

A non working Oven is not something any of us want to see. If you are technically handy, this is a good site to get instruction and fix some things yourself. If you do not feel confident doing your own repairs, an option is to visit Sears Home Services and use the scheduler. While you wait for the expert to review your model, you can check the bottom links for some possibilities. Hope this is of help.

Read More
Priscilla V -
September 26, 2011
A:

Thank you for your question and I understand your concern.

The electronic oven control/clock has most likely failed preventing the bake and broil elements from heating. The Electronic Oven Control (EOC) is part #316557511 which can be ordered from Sears PartsDirect .

The clock/oven control can be removed and replaced from the rear of the range by removing the panel from behind the console. NOTE: Disconnect the power cord from the power source before removing and replacing the clock/oven control. Pull one wire off at time from the old control and connected it to the corresponding terminal on the new control.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
September 27, 2011
A:

Hello I have a frigidaire wall gas oven model number FGB24L2ASA ,it will preheat then shuts off it will come back on but later and it doesnt keep the temp you set it goes off and on .please any ideas out there? thought might be the thermostat?

Read More
sandy -
January 16, 2012
A:

Sandy: I would suspect a weak glow bar oven igniter. If it takes a long time for the oven gas valve to open once the oven igniter cycles on, replace the oven igniter.

Read More
Joey S -
Sears Technician
January 17, 2012
A:

Joey,thanks also my broiler goes off after it gets so hot then it goes out also.on the frigidaire oven.

Read More
sandy -
January 17, 2012
A:

Sandy: The bake and broil are the same burners. The broiler will shut off once it reaches maximum temperature. When broiling; you do preheat the oven or the burner will cycle off once it reaches maximum temperature.

Read More
Joey S -
Sears Technician
January 17, 2012
A:

Joey is there a way to check the glo bar igniter ?

Read More
sandy -
January 17, 2012
A:

Sandy: If it glows and takes a long time for the oven to ignite, the glow bar is weak and needs to be replaced. Or, if you have a clamp on amperage meter, you can clamp the meter around one of the wires connecting the glow bar igniter and check the amperage/current draw. To save and work, if it's glowing but takes a long time to ignite, replace the igniter located towards the back of the broiler compartment.

Read More
Joey S -
Sears Technician
January 17, 2012
A:

Ok thanks Joey appreciate it will get it checked out.thanks

Read More
sandy -
January 17, 2012
See more answers

Top Parts