Model #79095300102 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore stove

A:

A stove is definitely something we depend on and when it begins to malfunction it can be a huge inconvenience. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. I hope the links that I provided are helpful. Have a great day!

Read More
Alina F. -
January 13, 2012
A:

Thank you for your question. I can understand your concern about this error code. The information you have received from Alina is correct. I'm also attaching the information for this error code below. First, try resetting the control by disconnecting the power for 30 seconds and then reconnect it. If the error code remains, the control # 316207502 will need to be replaced. I hope this will help you.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Scott D -
Sears Technician
January 16, 2012
See more answers
Q:

Kenmore Electric Stove

A:

I can understand your concern that you end up with enough moisture to form puddles on the stove top. I was checking the owner's manual and see on page 7 that it shows there is a vent right above the left burner so this may be normal depending upon what is baking, etc. I attached the manual in the link below if you would like to check while you wait for the expert to review the situation. Hope this information helps.

Read More
Barbara H. -
June 12, 2011
A:

Thank you for your question and I understand your concern.

Depending on the amount of moisture in the oven cavity during a bake cycle, the oven vent may condense water on the control panel and/or drip water onto the glass smoothtop. If your Kenmore range serial number falls in the range of VF121-VF236 then your range will need a new upper vent tube. The oven vent upper tube was redesigned to increase the air speed through the vent. This causes the air to flow past the cool surface of the backguard panel and prevents moisture from condensing on the panel. Order and install the new oven vent, part number 316208302.

To replace upper vent tube: Disconnect the power cord from the power source. From rear of range remove the upper and lower back panels. The oven vent tube is located on the right behind a rectangular vent heat shield. Remove the center and right screw attached to the vent heat shield. Lift the left side of the vent heat shield out of the tabbed slot. Slide the old vent tube off the lower tube coming from the oven cavity. Install the new tube in reverse. Reinstall vent heat shield and two screws; reinstall upper and lower rear panels and all screws.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
June 14, 2011
See more answers
Q:

i have a kenmore range model#790.95300102.....i keep getting flashing code ( f-1 ) and the baking element keeps getting very hot. what does the f-1 code means.

A:

I'm very sorry about the difficulties that you are experiencing Kenmore range. I did some research at managemylife.com and found an expert answer to a similar question that may assist you until your expert can respond. I have attached the link below. If you would like assistance from a qualified technician I have also attached a link to searshomeservices.com. I hope these links will help until your expert can answer.

Read More
James -
January 14, 2011
A:

Thank you for your question and I understand your concern.

The "F1" fault code generally means an Electronic Oven Control has failed. Disconnect the power, wait 30 seconds and reapply power. If the fault returns upon power-up, replace the EOC (electronic oven control). Disconnect the range from the power supply until the range has been repaired otherwise overheating can cause serious damage to the range.

If the fault code does not return upon power up, the oven temperature sensor should be removed and disconnected and tested for the proper resistance using an ohm meter. The oven temperature sensor can be access and tested from the rear of the range or it may be removable from inside the oven cavity. The temperature sensor is located in the left upper rear corner or in the right rear upper corner. See image I added below. The oven temperature sensor should measure approximately 1100 ohms at room temperature.

Parts can be ordered from Sears PartsDirect

NOTE: Disconnect the range from the power supply before servicing.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
January 15, 2011
See more answers

Top Parts