Model #79095201103 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

why does my microwave not heat on the convection setting ?

A:

I understand you are experiencing difficulties with your Microwave. Microwaves contain high voltage internal components that can retain a lethal electrical charge even when the microwave is completely unplugged. Door repairs and adjustments, even minor ones, can cause microwave leakage and a microwave shielding leakage test must be performed using a survey meter after any microwave service. This repair should be done only by a qualified service technician. I have provided a link To Sears Home Services if you decide to schedule service. It may be cost effective to just replace the unit, I have also provided a link to the Microwave section of Sears.com to price out what a replacement would cost.

Read More
Anna T -
October 24, 2012
A:

Thank you for your question and I understand your concern.

The model number you provided shows that it's a Free Standing Electric Kenmore range and not convection microwave.

There could be one of many possible failures preventing your microwave from heating.

I am sorry, but we do not give repair information on microwave ovens because they are inherently dangerous to service. Microwaves contain high voltage internal components that can retain a lethal electrical charge even when the microwave is completely unplugged. Door repairs and adjustments, even minor ones, can cause microwave leakage, and a microwave shielding leakage test must be performed using a survey meter after any microwave service. That's why I strongly warn you to have this repair handled only by a qualified service technician. You can schedule service online with Sears Home Services or by calling 1-800-4-MY-HOME.

Normally at ManageMyLife.com we like to help you with all of your repairs, but our expert advice is that microwaves are just too dangerous.

Read More
Joey S -
Sears Technician
October 25, 2012
See more answers
Q:

New oven part doesn't work

A:

I am sorry that you are having some difficulties with your repair and I will be happy to help. I did some research and I was able to find a link that will provide you with some good information. I hope this helps while you wait for your expert response.

Read More
Joseph P. -
May 30, 2012
A:

The part number for the control board for that model of range is 316207522. I recommend that you check the part number that you received. It should look like the control board in the photograph shown in the first image below. If you have the wrong control board, I recommend that you return it. If you ordered that control board from the Sears PartsDirect website, you can call 1-800-252-1698 to arrange an exchange or return.

If that control board is the same as the one shown below, then I recommend that you unplug the range and check the wiring connections on that control board. I provided a drawing of the control board and a wiring diagram in that second image that should help you check that wiring.

If the control board is wired correctly, then you could have a bad replacement control board.

There is not a reset or programming for that control board. The above tips should help you troubleshoot the problem that you are having. If you need more help, reply with additional details and we will try to assist you further.

If you get to the point where you need to have a service technician examine the range and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
June 01, 2012
See more answers
Q:

I have a problem with a Kenmore electric range. The oven temp has too wide temp range.

A:

I'm sorry that you are having difficulties. I did some research for you at managemylife.com and found an expert answer to a similar question that may assist you until your expert can respond. I have attached the link below.

Read More
James -
January 26, 2011
A:

Your voltage readings indicate the range should cook fine.

The customer should buy an oven thermometer. Don't buy the kind with a pointer and a spring. Get an oven thermometer with a bulb filled with liquid. The bulb type are accurate.

Set the oven to 350 degrees with the thermometer in the left upper rear corner of the oven for 30 minutes and write the temperature down. Move the thermometer to the upper front corner of the oven for 30 minutes and write the temperature down. Move the thermometer to the upper right rear, upper right front, center left rear, center left front, center right rear, and center right front of the oven. Leave the thermometer in each place for 30 minutes and write all readings down.

Compare the readings and see if they are within 15 degrees of each other.

If the temperatures vary in one position, there might be a void in the oven insulation.

If the temperatures are within 15 degrees of each other the oven should cook evenly. The customer needs to consider how they are placing food in the oven. The food has to have air circulation around it to cook evenly. If too much food is placed in the oven or pans are placed directly above or below other pans, the air doesn't circulate evenly.

A very good test of an oven is to cook a can of biscuits. Cook the biscuits exactly as the directions on the can recommend. If the biscuits cook good, the oven is ok. This would indicate the customer is doing something wrong.

Read More
Jimmy K -
Sears Technician
January 27, 2011
See more answers

Top Parts