Model #79095039700 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

My kenmore oven will not heat up

A:

Having your Oven not working correctly can be frustrating especailly when we use this appliance on a daily base. While you are waiting on an expert to answer your question, I was searching in the Manage My Life website and found a great link. I have attached the link below. Hope this is helpful!

Read More
Dezeray S -
March 07, 2011
A:

Thanks. This is a basic model and I have only had it since buying my new house 2 years ago.

Read More
jane -
March 07, 2011
A:

If neither the broil or bake will work the problem is usually a thermostat, broken wire, or the oven control.

If you will reply on this thread and include the model number of the range and details of what works and what doesn't, I will be glad to help.

Read More
Jimmy K -
Sears Technician
March 08, 2011
A:

Model # 790.95039700 Kenmor. I have only had it since 2008. Everything works. CLock, timer, oven light , all surface burners work. The oven just not heat up. I push the bake button, select temp and it clicks like it is heating up and I do hear a slight hum as if it is going to heat, but nothing, no glow, no heat at all.

Read More
jane -
March 08, 2011
A:

Thanks for sending the model number and details. You know the range is getting the proper voltage since the top burners and the oven light are working. Your range does not have a safety thermostat that could be causing the bake element no not work. Try broil and see if the broil element will heat. Inspect the bake element for any rough areas on it. When an element fails it will sometimes create an area on the outside of the coil that is very rough. If you find such an area, replace the element. Disconnect the power to the range and remove the covers on the rear of the range. Inspect the yellow wire that runs from the clock to the bake element, Inspect the orange wire that runs from the clock to the broil and bake elements. If you have an ohm meter, disconnect one wire from the bake element and check the resistance of the element. The bake and broil elements should read around 15-30 ohms resistance. If you still have questions reply on this thread and I will be glad to help.

Read More
Jimmy K -
Sears Technician
March 08, 2011
A:

No the broil does not work. I checked the coils and they are smooth, no rough spots and their is no spots where it looks like they burned out I do not have an ohm meter. I guess I will have to call a repair man. Do you think it is a part that needs to be replaced? Do you think it is the control panel or still the bake element? A repairman is going to cost 129.00 just to come out and diagnosis. Any other suggestions. Thank you.

Read More
jane -
March 08, 2011
A:

Since neither the bake or broil elements are working, I don't think the elements are the problem. I think the clock is the problem unless a wire is burned on the clock or elements. I don't want to recommend you replace the clock without some further testing. I guess you should get a technician to diagnose the problem.

Read More
Jimmy K -
Sears Technician
March 08, 2011
A:

Jimmy K..... I am having the exact same problems as Jane.. .316433604 is my model number. Kenmore . Everyone works except bake mode and clean mode

Read More
Wanda -
September 21, 2015
A:

My Kenmore Elite convection oven will not heat. I have had it repaired before and the repair was simple. The reason why the oven broke on both occasions is because I used it to heat the kitchen. I just need to know the part I need to buy to replace and have the oven work again. The repairman called the part a heating element. I cannot find a item with that description. Can you help?

Read More
Abbey -
October 24, 2015
A:

My Kenmore Elite convection oven will not heat. I have had it repaired before and the repair was simple. The reason why the oven broke on both occasions is because I used it to heat the kitchen. I just need to know the part I need to buy to replace and have the oven work again. The repairman called the part a heating element. I cannot find a item with that description. Can you help?

Read More
Abbey -
October 24, 2015
See more answers
Q:

Electric Range Stove Doesn't Get Hot 79095039700 Kenmore Electric range

A:

Thanks for the inquiry and for being a valued member.

I am sorry to hear that the oven or surface elements aren’t heating. I know how concerning that is to have happen.

Your symptoms suggest that you may have a blown house fuse or tripped breaker for the L2 leg of the power supply since no elements will heat. Check the house fuses or breakers for the range outlet. The breaker for the range will have two switches, and one of the two could be tripped, causing the loss of heat. If you find no problems there, I recommend that you unplug the range and check the LINE 2 wiring connection on the terminal block of the range. 

I recommend that you carefully measure the voltage at the range outlet. NOTE: You should only conduct this live outlet voltage check using a volt/ohm meter if you are completely confident in your technical ability to safely execute it.

If the voltage at the outlet is okay, then you could have a problem with the outlet cord. Unplug the range and use a volt/ohm meter to check the continuity through the power cord. If the power cord is bad then it will need to be replaced. If the power cord checks out, you will more than likely have a shorted relay on the control board.

If you would feel more confident have a Sears Home Service technician help assist with the diagnosis/repair, you can call 1-800-469-4663, or click here to be directed to the page to set up service.

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business.  

Read More
Jeff Wallace Sr -
Sears Technician
January 13, 2015
Q:

the broiler on my Kenmore stove does not work. 790.95039700. I bought aeplacement broiler unit; but the broiler still does not work

A:

I understand your concern on your Kenmore Stove/ Broiler is not working. I found a question in Manage My Life under the Answers button that was similar to the one you asked. I think this question will be very helpful to you, and give you some good advice on what to do. I attached the link below, I hope this helps!!!!

Read More
Raquel F -
August 24, 2010
A:

Unplug the range and remove the upper service panel from the back of the range. Check the wiring connections on the control board. Make sure that the blue wire is properly attached to the BROIL spade on the control board. If you have a volt/ohm meter, you can measure the resistance through the broil circuit. This would be through the blue wire and the orange wire connected to the L2 OUT spade. If the resistance through that circuit is between 10 and 40 ohms then the circuit should be okay. You could test the circuit by switching the blue broil wire over to the BAKE spade and placing the yellow bake wire on the BROIL spade. Reassemble the range and plug it in. See if the broil element will heat when you start the bake function. If it does, then you know that the circuit is good. Try the broil function to see if the bake element will heat using the broil function. It probably won't. This will verify that your failure is in the control board. The control board (part 316455420) is not that expensive (around $70). Replacing that part should fix this problem in this situation. NOTE: Be sure to unplug the range and switch the wires back to the proper spades on the control.

A problem with the original broil element could have caused your failure in the control board if that element was bad. If the original element is okay, then you may be able to return the element that you ordered. Contact Sears PartsDirect regarding the element if it is not needed for this repair.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

If you need more help, let me know.

Read More
Lyle W -
Sears Technician
August 25, 2010
See more answers

Top Parts