Model #79095033503 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

oven not working

A:

I understand that your oven is not working properly. I have attached a copy of your owners manual here, which will have some basic troubleshooting information for you to view while you wait on your response from an expert. I hope this is helpful. Have a great day!

Read More
Alina -
May 31, 2013
A:

Thank you for your question and I understand your concern.

If the surface elements will work, and the broil and bake element will not heat, I suspect the electronic oven control/clock assembly has failed. I added an image below showing the bake and broil circuit. When the oven is set to bake and started, 220-240 volts should be present across terminal L1 and terminal BK at the electronic oven control. If the voltage is not present, the electronic oven control part # 316455420 will need to be replaced.

NOTE: I do not recommend making any voltage measurements unless you have experience and feel safe and confident in doing so; otherwise I highly recommend calling a service technician to properly diagnose and repair your range.

Before replacing the electronic oven control, disconnect the power cord from the power source. 

The electronic oven control can be access and replaced from behind the range. You will need to remove the cover from behind the control panel to access the 4 screws securing the control to the bracket.  Also, make visual inspection of the bake and broil element and if it shows any signs of cracks or blistering, replace the oven element before installing the new control. If one of the oven elements happens to burn out and short, it will normally cause the oven control to fail.

You can look up and order parts for the Kenmore range model 790.95033503 at Searspartsdirect. 

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

Read More
Joey S -
Sears Technician
June 03, 2013
See more answers
Q:

kenmore range (oven not heating )

A:

Having your oven fail to heat can be a real headache. I did some research and provided a link to a similar question and answer on our site. I hope this will shed a little more light on the issue until the Expert responds to your question in more detail within 24 to 48 hours.

Read More
Julio -
May 16, 2013
A:

Hello Ed. I am sorry to hear about the problems that you are having with your Kenmore Range Model 790.95033503.

 

I assume that the stove top burners are still working. If not, then I recommend that you check the house circuit breakers or fuses for the range. You could have a problem with the L2 leg of the 240 volt power supply in that situation. The display will light up if only the 120 volt L1 leg of 240 volt power is supplied to the range. If that second L2 leg of 120 volt power is missing, the range will not heat.

 

If the stove top burners work, then you will probably need to replace the electronic clock control board in the range (part 316455420). That control board was probably damaged when the bake element broke and shorted out to the metal inside the oven cavity. If you replace that control board, you will normally need to replace the overlay (part 316220712) at the same time. That overlay covers and marks the selections buttons on the front of that control board. You can order parts from this page: Kenmore Range Model 790.95033503 Repair Parts

 

Be sure that you unplug the range before accessing internal components and replacing parts.

 

If you need more help, reply with additional details and we will assist you further.

 

 If you get to the point where you need to have a service technician examine and repair the range, you can schedule service through this link: Sears Home Services Range Repair.

Read More
Lyle W -
Sears Technician
May 18, 2013
See more answers
Q:

Kenmore Range model# 790.9503.3503

A:

Oven issues like this can be difficult to diagnose. While you wait for the expert response, I did locate two similar question with information that may be useful. I attached to the links below. I hope these help.

Read More
Barbara H. -
July 05, 2012
A:

Thank you for the information.

Read More
Johnny -
July 05, 2012
A:

Thank you for your question and I understand your concern.

If the surface elements operate; the range is getting the proper voltage supply and I would agree that the electronic oven control is most likely faulty.

Before condemning the electronic oven control/clock assembly; check for any loose or burnt wire connections at the range control and oven elements.

The electronic oven control #301455420 for model 790.95033503 range can be ordered from Sears Parts Direct. NOTE: Disconnect the power cord from the power source before removing the panel from behind the control panel and oven.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
July 09, 2012
See more answers

Top Parts