Model #79094851300 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore Electric Range Model 79094851300

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Alina F. -
December 22, 2011
A:

The image below shows the wiring diagram for your range. The L1 voltage through that burner switch is apparently closing the contact through that circuit traced in purple since the "element on" light illuminates. There could still be a problem with the burner switch, the wiring or the element. You could have a problem with the simmer select switch if your failure is on that left front burner.

I assume that only one burner is not working. You can check the element by switching it with the other one that is the same size to see if it works. You may have already done this. If the other burner element works in that position then you will need to replace that bad element. You can order parts from the Sears PartsDirect website.

If the element is not causing your problem, you can unplug the range and lift the cook top. Check for damage on that terminal block for the element that is not working. You may see that terminal block melted or the wire insulation discolored if that terminal block is bad. If you find no wiring problems, then the next step would be to check the wiring on that burner switch (with the range still unplugged ). If you have a volt/ohm meter, you can use the wiring diagram shown below to check the continuity through the burner switch (L1 to H1 and L2 to H2) if necessary. If that burner switch is bad, it will need to be replaced. You can check that simmer switch if the failure is in the left front burner.

These tips may help you fix this burner problem on your own. I you need more assistance, reply with additional details.

If you get to a point where you need to have a service technician repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
December 23, 2011
See more answers
Q:

Where is the fuse box/bank on a Kenmore free standing range?

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Jackie S -
October 31, 2011
A:

Based on your symptom the EOC has likely failed. The baking and broiling elements are controlled by the EOC. The EOC/Clock part# is 316207511. To install the EOC, unplug the range and remove the back panel of the console. Remove the wires from the old EOC one connection at a time and transfer them to the new EOC. Once all of the wires are transferred, remove the screws that secure the old EOC to the console. Remove the old EOC and mount the new EOC. Reassemble and test the control. Once you replace the EOC, you can test the functions to see if they are working properly. Parts can be purchased at the following link: Sears PartsDirect . I hope this helps.

Read More
Korinna S -
Sears Technician
November 02, 2011
See more answers
Q:

my oven says F1 and is beeping and wont let you open the door

A:

I'm sorry that you are having some difficulties with your Kenmore oven. Managemylife.com is a great web site to receive expert assistance to just about everything I did some research for you at managemylife.com and found an expert answer to a similar question that may shed some light on this problem. I have attached the link below. If you would like to schedule service from a qualified technician I have also attached a link to searshomeservices.com. I hope theses links will be helpful until your expert can respond.

Read More
James -
March 19, 2011
A:

The F1 error indicates the control thinks there is an over temperature in the oven. Most likely the sensor is the problem and will have to be replaced.

The sensor can be checked with a meter if you have one and are comfortable using it.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears�s technician. Here is a link for the website: Sears Home Services .

If you have a meter and do-it-yourself abilities then give me a reply and I'll provide more detail on how to access and check the sensor.

Read More
Fred M -
Sears Technician
March 20, 2011
See more answers

Top Parts