Model #79094473802 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drwaer
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

F30 Error... Any idea? 79094473802 Kenmore Electric range

A:

Thanks for the inquiry and for using SearsPartsDirect.com. 
I am sorry to hear of the F30 error code you are receiving on the unit, I know how frustrating that is to have occur.

The F30 indicates an open oven temperature sensor probe connection on the oven. This code is usually caused by a failed temperature probe or a failed wiring connection between the electronic oven control board and the probe. If you are able to unplug the range and access the probe and control board, then you can check the wiring connection and the resistance to determine the cause of this problem. You can pull off the back panel of the oven to access the oven temperature probe. It protrudes through the back wall of the oven. Unplug the wiring harness connection to the probe and check the resistance with a volt/ohm meter. At room temperature of 75 degrees, it should measure a resistance of 1091 ohms +/- 5.3 ohms. If the resistance is way off, then the probe will need to be replaced. If the resistance appears to be okay, check the wiring connection between the probe and the electronic range control board. 
If the wiring checks out, the control board will need replacement. If you have to replace the electronic control, you will also need to replace the overlay or push buttons that adhere to it.
If you need either part, I have provided blue links below that you may click on to be directed to the SearsParts site to view and purchase either or. 

Oven Temperature Probe Sensor for Model 79094473802

Electronic Control Board for Model 79094473802

Overlay for Model 79094473802

If you would feel more confident have a Sears Home Service technician help assist with the diagnosis/repair, you can call 1-800-349-5071, or click here to be directed to the page to set up service.
Hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
June 14, 2014
A:

Ok thank you, I'll take it apart and check that out, I appreciate your help! You guys are great! Thanks B.E.

Read More
BASSEM -
June 14, 2014
A:

So I ordered the Oven Temperature Probe Sensor for Model 79094473802, got it in the mail, but I can't figure out where it goes, do you have any diagram showing its location? Thanks

Read More
BASSEM -
June 29, 2014
A:

The oven temperature sensor probe pokes through the back wall of the oven at the top of the back panel inside the oven cavity.  The temperature sensor probe should be removable from inside the oven cavity. Remove the two screws and slowly begin pulling the sensor out until you come to a quick disconnect plug. You can disconnect the old and put the new one in it's place and reinstall it back in. 
If you look at the exploded view on SearsParts, its indicated as number 37 on the 'Body' schematic, which I've linked below so you can see it.

SearsParts Body Schematic


Read More
Jeff Wallace Sr -
Sears Technician
June 30, 2014
See more answers
Q:

Oven will heat, but not broil 79094473802 Kenmore Electric range

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is trouble with the range/oven.
 
Glad to help out.   Im  looking at your Kenmore range model number 79094473802.

Below is the way to check  your broil element at the top and Bake element at the bottom.

TESTING ELECTRIC RANGE ELEMENTS:
 
1.  Unplug th oven from the wall outlet.  
 
2.  Remove the racks from inside when you have the oven door opened.  
 
3.  The elements have a screw on each side and need to remove the screws and pull the wires from the
    elements out.
 
4.  Turn the dial on a multimeter to Rx1k.  Place one lead from the meter on the terminal at the end
    of the element, then place the other lead on the end of the other termial.  The needle on the
    multimeter should register between 19 and 115 ohms.  Replace the element if no reading registers
    on the meter.
 
5.  If the elements are good then take the meter and test both wires that you hook to the bake/broil
    elements.

Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".

Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry L -
Sears Technician
April 09, 2014
Q:

Triple burner element has resistance and power but not heating fully. 79094473802 Kenmore Electric range

A:

Thank you for your question and I understand your concern.

I assume you speaking of the triple element and not the simmer select.  The simmer select uses a simmer select control board which has nothing to do with the triple burner and triple burner switch.

There are only three components involved in the triple burner operation; the burner switch, the triple burner switch and the triple burner. If all three elements do not glow red, it could have a faulty triple burner switch. Based on your details, it could be a faulty triple burner switch or a faulty triple element. 

I added an image below of the wiring diagram that should be helpful. Keep in mind that the triple burner has a high limit switch which is part of the triple element which can also cause the burner to short cycle off and on too. The high limit switch can become weak and cause the burner to cycle off and on. 
 
If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.
 

Read More
Joey S -
Sears Technician
October 15, 2013
A:

Se we have replaced both the switch and the element and the problem still exists. The outer ring (third burner) has power it does light slightly but does not fully glow or fully heat but it does come on. And yes this is the triple burner.

Read More
Rebecca -
October 15, 2013
A:

So what happens is food in the center burns while stuff to the outside of the pan doesn't really cook.

Read More
Rebecca -
October 15, 2013
A:

Rebecca; The voltage supply will need to be measured across the terminals for the outer ring. The voltage must measure 220-240 volts. I added an image in my last reply of the wiring diagram ot use for making the voltage checks. If you do not have experience and feel safe and confident in measuring voltage, I strongly suggest calling a service technician to diagnose and repair your range. Also, make sure the new switch and element are wired up correctly.

Read More
Joey S -
Sears Technician
October 16, 2013
A:

I don't see the wiring diagram

Read More
Rebecca -
October 16, 2013
A:

Rebecca: The images are posted on the Manage My Life web site. Copy and paste the URL below in your browser and it will link you to the thread with the image of the wiring diagram. http://www.managemylife.com/mmh/questions/365349-triple-burner-element-resistance-power-heating-fully-79094473802-kenmore-electric-range

Read More
Joey S -
Sears Technician
October 16, 2013
See more answers

Top Parts