Model #79094464702 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

broiler element 790.94464702

A:

Thanks for the inquiry and for being a valued member.

Typically, if just one of the elements goes out, and the other (Bake) is still working fine, it's safe to assume it's an element issue.

However, you can take the bake element out and make sure it has power coming from the leads it plugs into. If it does, then the electronic control is providing it power, if not, it could be an electronic control board issue. 

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
October 09, 2014
Q:

Range died

A:

I am sorry that you are having some difficulties with your range and I will be happy to help. I did some research and I was able to find a link that will provide you with some good information. Click here for the link. I hope this helps with your research while you wait for your expert response.

Read More
Joseph P. -
July 06, 2013
A:

Thank you. My issue is different as there are no lights, nothing blinking, nothing works. It is completely dead.

Read More
Lisa -
July 06, 2013
A:

Thank you for choosing ManageMyLife.com. I understand how important it is to have a working range. Based on the symptoms you have provided, it sounds like the electronic controller needs to be replaced.
I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link below to be taken to the page.
Electronic Controller for Kenmore Electric Range Model # 79094464702
Below are instruction on replacing the board.
SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

1. Ensure that the range is completely cool. Unplug it from the wall.

2. Pull the range away from the wall so that the rear panel is accessible. If your range has an anti-tip plate installed, you may need to lift up on the front while pulling it out.

3. Remove the four screws securing the upper-rear panel to the range. Remove the panel.

4. Remove the four screws holding the control panel in place. Remove the control panel.

5. Peel the overlay off the of the front of the old control panel. Align and press it onto the front of the new control panel.

6. Align the new control panel with the screw holes. Secure the new control panel to the range with the screws that were removed.

7. Disconnect the wire harness from the old control panel. Connect it to the new control panel.

8. Replace the rear panel. Push the stove back into place and restore power to complete the installation.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services
If you have further questions please let me know. Thanks for using ManageMyLife.com.

Read More
Desirea -
Sears Technician
July 07, 2013
A:

Hi Thank you! I purchased this part and have installed it. The reason it needed to be replaced wasmdue to a connector blowing up in the back. A white plastic piece with an orange and a red wire threads thrumit. It attaches to two metal prongs. One melted. I cannot find a replacement piece. The part # may end in 4PC~G. That is on the part but the first part is melted off. Do you know where I can find this piece?

Read More
Lisa -
July 21, 2013
A:

Hi Lisa, sorry I have not gotten back to you sooner. I showing that you would only be able to replace the wire by replacing the entire wiring harness. I have included a link below for you.

Main Wire Harness for Model 790.94464702

If you have further questions please let me know.
Thanks for using ManageMyLife.com

Read More
Desirea -
Sears Technician
September 05, 2013
See more answers
Q:

Need help replacing outer glass on Kenmore Oven Door

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Jackie S -
December 01, 2011
A:

Thank you for your question.

I am sorry you are having a problem with the oven door. I know it can be frustrating when an appliance fails. I will be happy to assist you with replacing the door glass. I looked up the model number you have submitted. This does have tape securing the trim pieces in place to aid in putting the door together. Once the top trim and the handle assembly are installed it secures the trim. Instead of ordering the trim it you can use a piece of foil tape to hold the trim to the glass. The foil tape should hold up to the heat from the oven.

Before installing the new glass, make sure the door is not bent or twisted. The reason I say that is that the tempered glass could break right away again. Once you are confident the door is fine go ahead, attach the trim to the glass, and reassemble the door. I have found a video that shows how to remove the door take it apart. Click here to watch the video.

I hope this is helpful. Please let me know if you need further assistance.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
December 02, 2011
A:

Mark .... thanks for the info. The video is perfect. Only 1 question ... what kind of foil tape and do you know where I might buy it (Home Depot, Sears, etc.). Could you recommend a manufacturer or part number (or better description .. is it double sided). Could we use some kind of caulking/glue instead? Thanks!

Read More
Anonymous -
December 02, 2011
A:

I have done some further investigation and have found a part number for a foam tape that is used on the oven doors. The part number for the tape is 316066000 and can be ordered from the link below. I hope this is helpful. Please let me know if you need further assistance.

Read More
Mark T -
Sears Technician
December 03, 2011
See more answers

Top Parts