Model #79094343700 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

wiring difference on replacement part (electrolux) nr. range 790.94343700 -- when replacing current broken part no, 316135401

A:

I know that it can be very frustrating to have issues with your burner. The image below provides a picture on how the clips have changed. I have also provide the surface burner portion of the wiring diagram, so you can see what wires go to which numbers. If you don't feel comfortable doing this yourself, please click on this link to schedule service: Sears Home Services. Click on "Get Started" and follow the directions, click on the red "NEXT" button to continue. I hope this helps. Please feel free to let me know if you need further assistance. We are always here to help. Thank you for using Manage My Life.com.

Read More
AnneJ -
Sears Technician
November 10, 2013
Q:

Instructions for replacing a burner on a glasstop stove,

A:

It is always a little frustrating when an appliance or tool starts acting up on us. I think we all see money going right out the window when it happens. I'm sorry to hear that you are having some issues with your Kenmore glass top range. I did some research at Managemylife website and found an expert answer to a similar question that may help until your expert can respond. I have attached the link below so you can check it out. If you do decide to schedule service and have a qualified technician assist you, I have attached a link to SearsHomeServices.com. I hope the links below will help you.

Read More
James -
March 10, 2012
A:

Thank you for your question.

You pretty much have an idea how to replace the element. I am not sure if you have a bad element or not. When you have the burner switch turned on you should have 240 volts to the element. If you have this voltage and the element and the element is not working the element is defective. If you do not have the voltage, the problem is somewhere else. I have posted an image below that contains the wiring diagram. Just click on the image to enlarge it. Live voltage checks are dangerous, and possibly deadly. Exercise caution at all times. If you are not comfortable working with live electricity I suggest you call an experienced service technician.

Click here to watch a video on how to replace the element.

I hope this is helpful. Please let me know if you need further assistance.

Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
March 12, 2012
See more answers
Q:

Kenmore oven F10 error and overheating

A:

An error code can be concerning. I researched your question and was able to find a link with information on the f10 error code. I attached the link below. I hope this helps.

Read More
Jackie S -
January 27, 2012
A:

The error itself is a runaway temperature condition. If the oven is overheating disconnect power for 2-3 minutes. If it is still overheating the EOC (Electronic oven control part #316557118) may need to be replaced. You can order this part at Sears Parts Direct

The image below shows the procedure for accessing the sensor probe (p/n 316490000) which may be the issue as well. You can check the sensor by measuring the resistance through it with a volt/ohm meter. It should measure 1100 ohms at room temperature in most ranges. If it has extremely high resistance (over 3000 ohms) then the sensor will likely need to be replaced. Severe overheating may require the entire oven to be replaced if the damage is extensive. I hope this helps.

Read More
Joe G. - Personal Solutions Manager -
Sears Technician
January 28, 2012
See more answers

Top Parts