Model #79094321302 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

The oven on my Kenmore range is not working...model number is 79094321302. I was advised to replace the oven probe which we did, but it is still not working.

A:

I am sorry that you are having some difficulties with your oven and I will be happy to help. I did some research and I was able to find a link with a similar question. I am also adding a second link in where you can set service to have a certified technician fix your range. I hope this helps with your research while you wait for your expert response. 

Read More
Joseph P. -
March 14, 2013
A:

Thank you for your question and I understand your concern.

I assume the surface burners continue to heat and that both oven elements will not heat. Even if the broil element may work, I suspect it has a faulty electronic oven control/clock assembly. If the broil will heat, then it is possible to have a faulty bake element. Both oven elements are used doing the bake cycle. The broil element will alternate operation with the bake element.

Make visual inspection of the bake and broil element and look for any signs of cracks or blistering. If the oven elements appear normal, the elements are most likely Okay. 

If the bake and broil elements will not heat at all, the most likely failure is the electronic oven control/clock assembly. The electronic oven control will be likely need to be replaced as well as the clock overlay. The over lay must be applied over the new oven control before installation.

The oven control/clock assembly is part #316207511 and the clock overlay is part #316220841 which can be ordered from SearPartsDirect. 

The oven control/clock assembly can be accessed and replaced from behind the control panel.  Remove the cover from behind the control panel to access the oven control. The control is secured by a screw in each corner. Be sure to apply the new clock overlay on the oven control before installing the new oven control. NOTE: Disconnect the power cord from the power source before removing the cover from behind the console.  

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

 If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link:Sears Home Services.

Read More
Joey S -
Sears Technician
March 15, 2013
See more answers
Q:

can you send me the instructions on how to replace the probe in my kenmore oven, model # 79094321302

A:

Replacing a probe on a range may seem like a difficult task without the proper instructions. While you are waiting for an expert to respond I was able to locate some great information that could possibly assist you with your issue. I have added the link below. Hope this helps!

Read More
Yadira B -
February 24, 2013
A:

That link for a previous answer that Yadira B. posted in the above response has a video that shows how to replace that oven sensor probe. That information should help you replace that part. If you need more help, let us know.

Read More
Lyle W -
Sears Technician
February 26, 2013
See more answers
Q:

My Kenmore range needs a new probe. Sears is sending it to me, but I need instructions on how to install it.

A:

Managemylife.com is a great place to find the answers to just about anything, especially on appliances. I would suggest that you provide a little more information such as the make and complete model number of your product so your expert will be able to provide you the best possible answer. Just click on reply below where you can provide the additional information.

Read More
Yadira B -
February 24, 2013
A:

model # is 79094321302, kenmore self cleaning range

Read More
Judy -
February 24, 2013
A:

I posted an image below that will help you install that sensor probe. Unplug the range and remove the back panel to access that sensor probe on the back of the oven cavity. Unplug the wire harness and remove the screw that secures it to the outside back wall of the oven cavity.  Twist the sensor to release it from the slot in that back panel and pull it out. Push the new probe in place and mount it to the back of the oven. Plug the wire harness in and reassemble the range. 

 

I hope that this information helps. If you need more assistance, reply with additional details. 

Read More
Lyle W -
Sears Technician
February 26, 2013
See more answers

Top Parts