Model #79094214409 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Can a proficient home repairman replace the electronic control on his Kenmore electric slide in range? If not what is the estimated cost for this?

A:

To replace a electronic control is certainly a job that a man with modest experience will be able to do. I did locate a link that will discuss your situation in greater detail. Though this link discusses a different model number, the mechanics are likely going to be very similar. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instruction. I hope this link will help guide you in this repair and have a nice day.

Read More
Henry -
May 05, 2013
A:

Thank you for your question and I understand your concern.

You can find the Use and Care Guide at Manage My Life. Click on the blue link to open the Use and Care Guide.

You referred to your model range as being a slide in range, based on the model number provided, this is a freestanding range.

The electronic oven control (EOC) for model 790.94214409 is part #316557108 which can be ordered from Searspartsdirect.com.

To access and replace the electronic oven control will require pulling the range out and disconnecting the power cord. 

The cover behind the control panel will need to be removed by taking all the screws out from the panel. Remove the panel and you will have full access to remove and replace the electronic oven control. There will 4 screws securing the oven control, one screw in each corner will need to be taken out. Remove one wire/one connector at time from the old control and transfer the wire/connector to the new control board and reverse the procedure to install the new control.

You will also find a clock overlay over the old oven control/clock assembly that will need to be removed and re-attached to the new control. If the overlay does not stick well on the new control, the overlay should be ordered and installed before installing the new oven control board. 

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

Read More
Joey S -
Sears Technician
May 07, 2013
See more answers
Q:

Range model 79094214409, bottom element part# 316413800 damaged but top broil element still working.

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Alina F. -
November 22, 2011
A:

The heating element requires 240 volts in order to heat. This means it needs line one and line two voltages. The voltage must measure 240 when checking the voltage across the two leads of the bake element. I added an image below of the wiring circuit. If it does not measure 240 volts when measuring across the two leads of the bake element when the old bake element burnt out and shorted; it took out the oven control board. You will most likely have to remove and replace the electronic oven control. If you need further assistance please reply to this thread.

Read More
AnneJ -
Sears Technician
November 24, 2011
See more answers
Q:

Kenmore Electric Range

A:

Managemylife.com is a great place to find the answers to just about anything, especially on appliances. I'm sorry that you are having some difficulties with your Kenmore Range . I did a little research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links will help until your expert can respond.

Read More
James -
June 17, 2011
A:

I suspect the problem is caused by the infinite switch.

The diagram in the image below will help you with this problem.

First unplug the range.

The surface switches can be reached by removing the rear panel. See if you can locate the terminal "P" on the switch. You can try removing the that wire and see if the surface indicator light goes out. Most likely on one switch is bad.

You can reply with any additional details or questions for further assistance.

Read More
Fred M -
Sears Technician
June 18, 2011
See more answers

Top Parts