Model #79094001403 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

I want to order circuit for my oven. but i cant find it. 79094001403 Kenmore Electric range

A:

Thanks for the inquiry and for being a valued member.

I am sorry to hear of the issue you've had with the mouse frying the circuit board. I know how frustrating that is.

I presume you are referring to the electronic control for the display. The part number for the board is 316557106. I would also recommend replacing the overlay, which is part number 316419106. 

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
February 23, 2015
Q:

kenmore oven

A:

A non working Oven is not something any of us want to see. If you are technically handy, this is a good site to get instruction and fix some things yourself. If you do not feel confident doing your own repairs, an option is to visit Sears Home Services and use the scheduler. While you wait for the expert to review your model, you can check the bottom links for some possibilities. Hope this is of help.

Read More
Priscilla V -
January 26, 2012
A:

You will probably need to replace the oven temperature sensor probe. The technical explanations of those codes are shown in the image below. There is a chance that you could have a problem with the wiring harness or the clock control board that is causing this problem.

Before you order that part, I recommend that you unplug the range and check the resistance of that oven temperature sensor probe using a volt/ohm meter before ordering that part. Here is a link for a brief repair video that shows how to test that sensor: Oven Sensor Testing . That sensor should measure around 1086 ohms at room temperature. If it is bad, you can order the replacement sensor from the Sears PartsDirect website. The part number is 316490001. Here is a direct link for that part: Sensor Probe .

Be sure that you unplug the range before accessing and replacing internal components.

If that sensor is okay, I recommend that you plug the sensor probe back into the harness and check the resistance of the entire sensor circuit from the connection on the clock control board (with the range still unplugged ). If the sensor resistance is okay from that location, then you will need to replace the clock control board. If the resistance is high or "open" from the control board, then you apparently have a problem with that wire harness for the sensor. The most frequent failure of the harness occurs in the disconnect plug at the probe. You may need to cut that disconnect plug off and connect those sensor wires properly using ceramic wire nuts in that situation.

I hope that this information helps. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
January 27, 2012
See more answers
Q:

Kenmore electric range burner element

A:

When replacing a new part on a appliance it can feel like such a relief since you fixed a little part of it. I have taken some time to research your question here on the Manage My Life website and I noticed that someone else had asked a similar question with a posted response from an expert. I attached the link below for you to view. I hope the link that I provided is helpful.

Read More
Alina F. -
February 13, 2011
A:

The electric coil elements will tend to stick up and not rest level. You can try placing a heavy pot or pan on the coil. A cast iron skillet would be best if you have one. Leave the heavy pan or pot on the burner for a few days. This will eventually cause the leads on the element to bend slightly and may fix your problem.

If you are looking for a quicker fix, you can try to slightly bend the metal terminals on the element so that it will rest in a level position and not stick up. Make very gradual adjustments using pliers and do not bend those elements severely. This could cause a short in the element.

I hope that these tips help. Sometimes there is no way to resolve this problem. The burner sticking up will not really hurt anything even though it does not look so good.

If you need more help, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
February 15, 2011
See more answers

Top Parts