Model #79092680301 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

How do I know if my coils in my Kenmore Electric Range Oven blew?

A:

Good morning... I can fully understand your concern regarding your oven throwing the breaker and making a popping sound. I did locate a link that will discuss this situation in greater detail. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instruction. I hope this link will help guide you as to what might wrong with your oven and have a nice day.

Read More
Henry -
December 16, 2012
A:

Thank you for your question and I understand your concern.

Disconnect the range from the power supply and then make an inspection of the bake and broil elements. Look for any signs of blisters or cracks. If the bake and broil elements appear Okay and neither bake or broil element will heat, the electronic oven control/clock assembly has most likely failed. The clock/oven control can be accessed by removing the panel from behind the control panel. Look for any signs on the board for darkened or burnt areas.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
December 17, 2012
See more answers
Q:

heating sensor

A:

Having to get information for an appliance can be a challenge. While you are waiting for an expert to reply I recommend visiting the sears parts direct website were you can view a parts diagram as well parts list to your model. Below I have attached the link.

Read More
Priscilla V -
March 08, 2011
A:

been there done that .diagram not available people I spoke with do not know what they are talking about.. they just want to sell me parts that I dont need. very dissatisfied

Read More
jeff -
March 08, 2011
A:

I'm sorry you are having this problem. The thermostat on this range is built into the electronic control. If this is what you're looking for, the part number is 316207511. There is also a sensor inside the oven that senses the temperature and sends a signal to the control. This sensor number is 316233902. Both of these parts are available at SearsPartsDirect . I hope this helps you. If you would like more assistance, any additional details will be helpful and I will be glad to assist you further.

Read More
Scott D -
Sears Technician
March 09, 2011
A:

thank you scott. i finally got an F3 code and ordered the sensor probe.

Read More
jeff -
March 09, 2011
See more answers
Q:

Why is my Kenmore electric range beeping and displaying a flashing error code F1?

A:

Normally there is not a simple reset for this error code. If you have not tried unplugging the range for several minutes (or shutting off the breaker) to completely disconnect electrical power then you may try that tactic to reset the control board. Sometimes the control board will reboot and clear the fault code if it was caused by a power surge or glitch experience through the electrical lines.

If the F1 code returns after powering the range back up then it is caused by one of these failures:

  • Shorted keypad -- the control board will need to be replaced
  • Control board has an internal memory failure -- the control board will need to be replaced
  • Control has sensed a runaway temperature -- Your details suggest that the F1 is being displayed while the oven is at room temperature. In this situation, you would need to check the resistance of the oven temperature sensor probe. At room temperature, the resistance should be about 1100 ohms. If resistance of the temperature probe is over 2000 ohms then replacing the temperature probe would fix this problem.

The temperature probe is mounted on the upper back inside wall of the oven. You can unplug the range and remove the screws that mount it to the back wall. Carefully pull the probe into the cavity of the oven until you encounter the wire harness disconnect plug. Unplug the probe and check the resistance of the component using a volt/ohm meter. (You can normally purchase a meter for less than $20 at your local hardware store or Sears store if you don't have one.) If the resistance measured directly at the probe is okay then the next step would be to plug the probe back in and check the resistance through the temperature probe circuit that plugs into the control board in the console. With the range still unplugged, remove the upper back panel to access the control board. The image below shows the connections of the temperature probe circuit on the P5 plug. The probe circuit wires are normally violet. If you measure normal resistance through the probe circuit (1100 ohms) then the control board will need to be replaced.

You can order parts from the Sears PartsDirect website.

If you need more help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
December 11, 2009

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show