Model #79092423301 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

how to fix the f1 error code for a oven

A:

Thank you for your question. The "F1" fault code indicates an error in the electronic oven control circuitry. The failure is most likely the electronic oven control board and a slight possibility of a faulty oven temperature sensor probe. The oven temperature sensor should have a resistance measurement of 1050 to 1100 ohms at room temperature. The oven temperature sensor can be remove from inside the oven cavity and tested using an ohm meter. If the sensor measures approximately 1050 to 1100 ohms, replace the oven control board. Click here toget a wire diagram and the parts if needed.

Thank you for choosing Manage My Life.

Read More
dtova00 -
Sears Technician
September 09, 2013
Q:

oven model # 79092423301 oven tripped breaker now showing f01 hard reset not working how to troubleshoot this oven?

A:

I understand that you are getting the error code f01 on your oven. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina F. -
April 07, 2012
A:

The technical description of the error codes on that range is shown in the image below. You will probably need to replace that clock control board in the console (part 316207511). There is a chance that a bad oven temperature sensor could be causing that F01 code. Before replacing that control board, I recommend that you check the oven temperature sensor probe resistance as shown in this repair video: Oven Sensor Testing . You can access that temperature sensor probe as shown in this video: Oven Temperature Sensor Probe Replacement . Be sure that you unplug the range before accessing internal components. That sensor should measure around 1100 ohms at room temperature. If that sensor is bad, then it will need to be replaced. The part number for the sensor is 316233902. Here is a direct link for that part: Oven Temperature Sensor Probe for Kenmore Range 790.92423301 . Replacing that sensor probe would be much less expensive than replacing the clock control board if that component is causing the F01 code.

If that sensor is okay, then you can plug that sensor back into the harness and access that clock control board as shown in this video (with the range still unplugged ): Range Clock Control Replacement . You don't have to remove that control board yet. I recommend that you check the resistance through the entire sensor circuit from the control board. That sensor circuit is connected to the control board through violet wires. High resistance through the sensor circuit could also cause that F01 code. You should measure the same resistance of 1100 ohms through that sensor circuit where it connects to the control board. If the resistance through that circuit is high (over 2000 ohms at room temperature) then I recommend that you check that harness. The most suspect location for a wire harness failure is the disconnect plug directly at the sensor probe. You may need to cut that disconnect plug out of the circuit and connect those sensor wires using ceramic wire nuts.

If that sensor resistance is normal when measured from the control board, I recommend that you replace that clock control board. Here is a direct link for that part: Clock Control Board for Kenmore Range 790.92423301 . You may also need to order and replace that overlay unless you can reuse the original one as shown in that repair video.

NOTE: Since the breaker tripped, I also recommend that you check the bake and broil elements for damage. A shorted bake or broil element could have caused the breaker to trip and could also damage that control board.

These tips should help you fix this range problem on your own. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
April 09, 2012
See more answers
Q:

i have a kenmore eletric stove after i used the self clearing the oven will not work

A:

I'm sorry about the difficulties that you are experiencing with your Kenmore electric stove . I did some research at managemylife.com and found an expert answer to a similar question that may assist you until your expert can respond. I have attached the link below. If you would like to schedule service and have a qualified technician help you, I have also attached a link to searshomeservices.com. I hope these links will help until your expert can respond.

Read More
James -
March 25, 2011
A:

The link for a previous answer that James R. provided in the above response pertains to a gas range. The model number that you submitted in your details indicates that this is an electric range. Here are some tips that may help you with this problem:

  1. Check to see if the cook top burners work properly. If not, then I recommend that you check the house electrical circuit breakers/fuses for the range. If the cook top burners will not heat, this is often caused by an electrical supply problem going to the range.
  2. If the cook top burners heat, I recommend that you unplug the range and check the wiring on the back electronic control board in the console. Here is a video that shows how to access that control board in the console: Range Clock Control Replacement . Check the red wire on the L2 IN spade and the orange wire on the L2 OUT spade of the control board. If these wires are connected properly, then you may need to replace that electronic control board (part 316207511). Check the control board for burned spots are evidence of damage. You can order that control board from the Sears PartsDirect website if it is apparently burnt.

Be sure that you unplug the range to disconnect electrical power before accessing internal components.

There is a risk involved in replacing that control board without further diagnosis. A technician will normally check the live voltage going into and coming out of that control board in the bake and broil modes to check the control board. Those live voltage checks are dangerous. I recommend that you have a service technician conduct those tests if you want to make sure that the control board is bad before replacing it. Here is a link for the Sears Service website in case you need it: Sears Home Services .

If you need more help, reply with additional details and we will try to assist you further.

Read More
Lyle W -
Sears Technician
March 26, 2011
See more answers

Top Parts