Model #79092403010 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

Oven not working 790.92403010

A:

Thank you for choosing SearsPartsDirect. I will be more than happy to assist you with your Kenmore range.

From the information you have provided above, it seems to me as if your baking element is defective. If all other setting are working there’s a good chance you just need your replace the element. It could also be an issue with the mother board but id suggest starting with the element first.

I hope you found this information useful. Again thank you for choosing Sears, we appreciate your business, have a great day

Read More
Benny23 -
Sears Technician
January 09, 2015
Q:

How much weight can a glass top on a Kenmore range hold?

A:

I could surly understand your wife's concern upon how much weight the glass top can handle. I located some general information that an expert provided upon the subject. I hope that it's helpful in deciding what to do.

Read More
celene -
December 05, 2010
A:

The link for a previous answer provided by Celene in the above response gives some weight guidelines for a similar glass top range. There is technically not a weight limit on the glass top. About 45 lbs. is the maximum load that is recommended on top of an element. The pot should not extend more then 1 1/2" past the outside of the marked burner ring. It is likely that the glass top will hold a 16 qt. pot that is nearly full of boiling water without any problems if it fits the burner ring. I personally would not use it on my glass top range. Prolonged exposure to this weight may weaken the glass/ceramic top. Unless you can completely lift that pot and move it, it will likely cause some sever scratches on the surface of the range.

If you are considering using the glass top range for canning, I recommend that you use a hot plate or outside propane burner instead. The radiant elements will not normally work very well for canning purposes. A limiter will shut down the element to protect the glass top when it gets too hot. This can interfere with the canning process.

I hope that this information helps. If you need more assistance, reply with additional details and the full model number of your Kenmore range.

Read More
Lyle W -
Sears Technician
December 07, 2010
A:

model #790.92403010 When I purchased this range I bought the one with the bigger burners because I planned to can etc. ..Now my ? is kind of the same can my stove top hold a 24 quart stainless steel yes flat bottom stock pot as I want to make a ALE and it is recommended to boil as much of the 5 gallons as possable for the best turn out..

Read More
Kelly -
February 07, 2013
A:

Hello Kelly. That ceramic glass cooktop should support the 24 qt. stainless steel stock pot that you are describing. Be careful not to slide the pot across the top of the cooktop when it is full.

Read More
Lyle W -
Sears Technician
February 08, 2013
See more answers
Q:

Kenmore Electric Range Stopped Working

A:

Managemylie.com is the place to go for answers when you continue having problems with the Kenmore range. An expert will respond to your specific questions within 24-48 hours. Meanwhile I am attaching a link that may be of some help.

Read More
Anna T -
July 09, 2012
A:

I have solved the problem and it wasn't the range. I hooked my multimeter up to the plug and realized it was only pulling 110 and not 220. After correcting the plug it started working again.

Read More
Brad -
July 10, 2012
A:

Thank you for your question and I understand your concern.

The range must have 220 volts in order for the surface elements and oven to heat. The clock only requires 110 volts in order to power up. The range needs line one and line two voltages of 110 volts which will provide 220 volts to the range. You mentioned you tested the wires for power but you did not indicate the voltage reading. You will need a voltage meter to check the voltage and not just a tester with a light. Based on your symptom and details it sounds like the range is not getting the proper voltage or possibly a floating neutral supply. You mentioned checking the circuit breakers dedicated for the range but did you reset them? Locate the two house circuit breakers dedicated for the range and reset both breakers. Flip both breakers off and on 2-3 times and then see if the oven and surface elements will heat. If it does not heat, I strongly suggest calling a service technician to diagnose and repair your range.

You can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
July 12, 2012
See more answers

Top Parts