Model #79092322301 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Oven and broiler not working 79092322301 Kenmore Electric range

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
James -
May 04, 2013
A:

Thank you for your question and I understand your concern.

Based on your symptom and details, if the cooktop is still working, this means the range getting the proper voltage supply.  The electronic oven control/clock assembly will likely need to be replaced. In order to confirm if the electronic oven control will need to be replaced will require measuring and confirming the voltage supply at the electronic oven control/clock assembly. The power supply that powers up the electronic oven control is measured across the black wire connected to terminal L1 and the white wire on the 15 pin wire connector. If 110-120 volts is measured, the electronic oven control/clock assembly will need to be replaced. I added an image below and I traced the circuit that powers up the clock/oven control in black and green. I traced the neutral circuit in green because white will not show up on a white background.

NOTE: I do not recommend making any voltage measurements unless you have experience and feel safe and confident in doing so; otherwise I recommend calling a service technician to diagnose and repair your range. 

 If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

 

Read More
Joey S -
Sears Technician
May 06, 2013
A:

I don't see the image that you referred to in your response. Would you resend the image. Thank you for your assistance. Dave

Read More
David -
May 07, 2013
A:

David: Copy and paste the URL below in your browser and you should be able to view the image. http://www.managemylife.com/images/34636/original/79092322301_dead_EOC_test_points.JPG?1367859801

Read More
Joey S -
Sears Technician
May 07, 2013
See more answers
Q:

Kenmore electric oven not working

A:

When the oven works one day and not the next it can be confusing and upsetting. Diagnosing electric ovens is not easy. I did find a similar question from a previous expert post that may help while you wait for the expert to review your model. If you decide you would prefer to have an experienced technician visit to diagnose and make repairs, an option is Sears Home Services. I attached that link below also. Hope this helps get your oven back to normal.

Read More
Barbara H. -
January 23, 2011
A:

Thank you for your question and I understand your concern. Since the surface elements work normally this would indicate the range is getting the proper voltage supply. If both elements (bake and broil) quit heating at the same time, the most probable failure is the oven control board. The bake and broil elements have a L2 (line 2 voltage) in common with both. If the control board fails to provide L2 voltage, neither element in the oven will work. See image below.

In order to properly diagnose the failure, check voltage across L2 out terminal and the Bake and Broil terminals when set to bake and then broil. Place the voltage meter leads on L2 out terminal at all times and place the other meter lead on BK and then on BRL. If it does not measure 220-240 volts, replace the oven control board. You can access the control board by removing the panel from behind the console. NOTE: I do not recommend checking voltages unless you have experience and feel safe and confident in doing so, otherwise I recommend calling a service technician to diagnose and repair your range.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services

Read More
Joey S -
Sears Technician
January 24, 2011
See more answers

Top Parts