Model #79090313010 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

F10 error 79090313010 Kenmore Electric range

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Dezeray S -
July 15, 2013
A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com

I am sorry and do understand your frustration when you are seeing that F10 code on your range.

The F10 error code can be cause by irregularities in the power supply or a failure in the control board snesor circuit or stuck relay.  It says the thing to do please is turn off the range circuit breaker for 30 seconds, then turn it back on.

Good luck.   If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com

Read More
Larry L -
Sears Technician
July 15, 2013
A:

Thanks for the response. It is still happening. So, How do I determine if the cause is the control board sensor circuit or the relay?

Read More
ANDREW -
July 15, 2013
A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com

Thanks for writting back and letting us know.   Sorry you are still having the same trouble with the range.  

Allow us to show you the BEST our www.ManageMyLife.com website has to offer! Not only is this completely free, but we have troubleshooting experts who can provide you with tons of information from installing a part to maintaining your closest. In order to join our growing community of do it yourselfer's all we need is your email address and zip code and you're all set!

If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com

 

 

Read More
Larry L -
Sears Technician
July 15, 2013
See more answers
Q:

electric oven 79090313010 bake don't work

A:

It can be very frustrating when your range does not want to heat up. I did some research on the problem and provided a link to a similar question and answer on our site. I hope this will shed a little more light on the issue until the Expert responds to your question in more detail within 24 to 48 hours.

Read More
Julio -
August 27, 2012
A:

Thank you for your question and I understand your concern.

If the upper surface elements operate and the broil element, it could have a faulty bake element, faulty electronic oven control or a burnt wire connection. The bake element can be disconnected and tested for resistance/continuity with an Ohm meter. If the bake element is Okay, I would suspect a faulty electronic oven control board/clock assembly. The bake element requires 220 volts in order to heat. If the bake element is not getting 220 volts, the electronic oven control board as most likely failed. NOTE: I do not recommend measuring voltage unless you have experience and feel safe and confident in doing so; otherwise I strongly suggest calling a service technician to diagnose and repair your range.

The oven control can be accessed and replaced from the rear of the range. Disconnect the power cord from the power source before removing the panel from behind the control panel.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
August 29, 2012
See more answers
Q:

Kenmore 790.90313010

A:

It is always frustarting to have a major appliance to be acting up. I'm sorry to hear that you are having some difficulties with your Kenmore Electric Range. I did some research for you at Managemylife and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices. I hope these links provided assist you.

Read More
James -
February 11, 2012
A:

Thank you for your question and I understand your concern.

If the range was working before the move, I suspect an electrical supply issue.

Based on your symptom and details, there is likely a problem with the electrical supply on the Neutral side. It could have a faulty/loose Neutral supply. The voltage supply and neutral will need to be checked by the electrician when the range oven is plugged in and when under a current load.

I recommend having the electrician come out a check the electrical supply as well as for a floating Neutral.

This may be the issue. If not, please reply and I will be glad to assist you further.

Read More
Joey S -
Sears Technician
February 13, 2012
See more answers

Top Parts