Model #7907861850B KENMORE Free Standing, Gas

  • Backguard
    3 Results
  • Burner
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

kenmore oven won,t ignite 7907861850B Kenmore Gas range

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your range is not working properly.

 
You will need to test the safety valve and the sensor probe. 


GAS SAFETY VALVE: 1.5 Ω
BAKE IGNITOR:  108 / 232 voltage   100 Ω

OVEN TEMPERATURE SENSOR PROBE: 1100 Ω * refer to chart attached. 

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the unit before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.


Read More
Natasha12 -
Sears Technician
August 11, 2015
Q:

flashing F 10 and does not operate. 7907861850B Kenmore Gas range

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is the F 10 code of the gas range.
 
Glad to help out.   Im  looking at your Kenmore Gas Range model number 7907861850B.

F 10:

LIKELY FAILURE CONDITION/CAUSE:
RUNAWAY TEMPERATURE.

Suggested corrections.

1.   Check the sensor probe and replace if necessary.
2.  If oven is overheating, disconnect power.
3.  If oven continues to overheat when the power is reapplied, replace control board. 
4.  Severe overheating may require oven to be replaced should damage be extensive.

Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry L -
Sears Technician
April 21, 2014
Q:

My oven does not work

A:

I understand how inconvenient it is when your unable to operate your some features on your range. While your waiting for5 an expert to respond, I attached a couple links that you might find helpful!

Read More
Jackie S -
September 04, 2011
A:

When you turn the broiler on you should see the ignitor glow bright red. The oven safety valve should open within 40 seconds and the burner will light. The bake burner goes through this same process. You should be able to the the glow of the ignitor through the slits in the oven bottom. Don't put your head into the oven cavity, you can see the glow from outside the door opening.

If the bake ignitor is not glowing, you could have a problem with the bake ignitor, the electronic oven control, or the oven safety valve.

To test the ignitor someone will need to test the voltage to the bake ignitor. If you have 120 volts ac to the bake ignitor and it is not glowing, replace the ignitor.

If you have questions,reply on this thread and I will be glad to help.

If you are not comfortable doing these tests, you can go to Home Services and get a Sears technician to repair the range.

Read More
Jimmy K -
Sears Technician
September 06, 2011
A:

I have install a lower element and a timer and clock. Everything was working fine, but the next morning, nother worked. Do I have to call a Sear gechnician to repait the range

Read More
Paul -
February 23, 2013
See more answers

Top Parts