Model #79077449804 KENMORE Free Standing, Gas

  • Backguard
    3 Results
  • Burner
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

code31 79077449804 Kenmore Gas range

A:

Thanks for the inquiry and for using SearsPartsDirect.com.
I just responded to the F13 error code, and in regards to F31, it indicates 'shorted probe circuit.' This could indicate a shorted RTD Sensor Probe or could be an issue with the EOC. Since F13 was an EOC error, I suspect F31 will also be with the EOC, but it would be wise to test the oven's temperature probe sensor. 
Check resistance at room temperature, if less than 500 ohms, replace the sensor probe. Check for open or shorted sensor probe harness between EOC & sensor probe connector. 
If you would feel more confident have a Sears Home Service technician help assist with the diagnosis/repair, you can call 1-800-349-5071, or click here to be directed to the page to set up service.
If you by chance need a replacement oven temp sensor probe, I have provided a blue link below that you may click on to be directed to SearsParts to view and purchase if needed.

Oven Temperature Probe Sensor for Model 79077449804

Hope this helps and thanks for using SearsPartsDirect.com.

Read More
Jeff Wallace Sr -
Sears Technician
April 05, 2014
Q:

Code F13 790.77449804

A:

Thanks for the inquiry and for using SearsPartsDirect.com.
I am sorry to hear of the error code you are receiving with the gas range, I know how frustrating that is to have occur.
The F13 error code indicates 'a bad EEPROM identification/checksum error.'
The only option to clear this error would be to disconnect power for 30 seconds and reapply power.
If the fault returns upon power-up, replace the EOC or electronic control board and overlay.
If by chance you need the EOC and Overlay, I have included  blue links below that you can click on to be directed to SearsParts to view and purchase if needed. 

Electronic Control Board for Model 790.77449804

Overlay for Model 790.77449804

Hope this helps and thanks for using SearsPartsDirect.com.

Read More
Jeff Wallace Sr -
Sears Technician
April 05, 2014
Q:

My Kenmore range reads error f 13. What is the part EOC (electronic over control) that it suggests I replace?

A:

When there is baking to be done and the oven malfunctions, it is upsetting. I hope you did not have any batter or bread ready to go into the oven. I have done some research on the Manage My Life website and have located a link similar to your issue. While you are waiting for a detailed reply from an expert I have provided the link below. Hope this helps!

Read More
Priscilla V -
August 01, 2012
A:

I see Priscilla provided you with excellent information. If you have a 790. model range with the F13 code being displayed, then I would suggest that you remove power to the range for at least one minute and then restore the power and set the clock for the time of day. If the code does not come back you have solved the problem.

If it does come back then you will need to replace the Electronic Oven Control. The electronic oven control is the clock/digital display behind the control panel.

Parts can be purchased from Sears PartsDirect . You will need the complete model number of the range to access the parts list diagram for your model. I hope this helps.

Read More
Korinna S -
Sears Technician
August 01, 2012
A:

I need the part #'s for the control board and the overlay to the control board on my Kenmore range model # 790.77449804

Read More
Jennifer -
August 04, 2012
A:

The control board is 316557211 and the overlay is 316419306. I hope this helps.

Read More
Korinna S -
Sears Technician
August 17, 2012
See more answers

Top Parts