Model #79075851302 KENMORE Free Standing, Gas

  • Backguard
    3 Results
  • Burner
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore gas range, model #790

A:

I understand that your Kenmore gas range has no power to it. While you are waiting for an expert to respond, I have attached a helpful link below that may provide information to assist you with your question. I would recommend you reply back to this thread with a complete model number to your question. I hope the link that I provided is helpful. Have a great day!

Read More
Alina F. -
June 02, 2012
A:

Thank you for your question and I understand your concern.

Without knowing the complete model number of your Kenmore range I can only provide general information.

Based on your details, it sounds like it could have a faulty electronic oven control board or the control board lost the power supply in order to power up.

So that's what I can tell you at this point. I can give you more detailed help if you could provide me with the complete model number. The model numbers are typically located behind the oven door along the oven cavity opening or along the frame behind the broiler/storage drawer. If you could supply me with that information I will be happy to assist you further.

Read More
Joey S -
Sears Technician
June 04, 2012
A:

Thanks so much for the reply. Model # is 79077433900. I have reset all the power to the kitchen and that is the only appliance which is not responding. Is the board fairly easy to swap out?

Read More
Dawn -
June 04, 2012
A:

Dawn: The electronic oven control is easy to access and replace. You access the electronic oven control by removing the panel from behind the control panel. Just be sure to disconnect the power cord from the power source before removing the panel from behind the control panel. The control is fastened by 4 screws in each corner. Remove and transfer one wire at a time from the old control board to the new one and you can't go wrong. The part number of the electronic oven control (EOC) is #316557211.

Read More
Joey S -
Sears Technician
June 04, 2012
A:

have a kenmore gas range and have lost all electrical, model 790

Read More
kelly -
November 20, 2012
A:

Kelly: I will need to have the complete model number in order to provide specific troubleshooting assistance. If the surface igniters are not working and the clock/oven control is dead and the oven cavity light is not working, it sounds like its lost voltage between the outlet and the range. Try plugging another appliance or something in the outlet to confirm it works. So that's what I can tell you at this point. I can give you more detailed help if you could provide me with the complete model number. If you could supply me with that information I will be happy to assist you further.

Read More
Joey S -
Sears Technician
November 21, 2012
A:

kenmore gas range model 79075851302 oven won't light, top burners work as does the broiler.

Read More
Joan -
February 03, 2013
A:

Joan; In order for the bake burner to come on and heat, the bake igniter must receive voltage from the electronic oven control/clock assembly and the bake igniter must glow and pull enough current/amperage to open the oven gas valve. You will need to remove the oven floor and flame spreader and then turn the oven on to bake and see if the bake igniter will glow or not. If it does not glow, it could have a broken igniter, faulty electronic oven control/clock assembly and/or slight possibility of an open circuit in the oven gas valve. The bake igniter must have a 120 voltage supply in order for it to glow. If the bake igniter is glowing, the bake igniter is weak and not pulling enough current/amperage to open the oven gas valve. The bake igniter can be disconnected and tested with an Ohm meter for resistance/continuity. Note: Disconnect the power cord from the power source before disconnecting and testing the bake igniter for resistance/continuity.

Read More
Joey S -
Sears Technician
February 04, 2013
A:

I have the Kenmore Gas Range Model 790.7433. In the minimum and maximum control settings it says that the convection oven should be able to be set as low as 170 degrees. But in the directions for using the convection oven it says that it can only be set between 300 and 550 degrees. I am trying to bake some granola that needs to be set at 200 degrees. I'd really like to use the convection at this temperature because it would cook it better. Is there a way to set the convection temperature to 200 degrees?

Read More
Victoria -
May 26, 2015
See more answers
Q:

Can I paint the grates for my Kenmore gas range, if so does Sears have a paint available? 79075851302 Kenmore Gas range

A:

Thank you for the inquiry and for using ManageMyLife.com. I can definitely appreciate wanting to refurbish the grates, as cast-iron grates can become quite an investment to replace as they are costly to produce.

You may refinish the grates, as long as you use temperature-resistant paint, standard paint won't work because of the heat they have to endure. Typically they are cermaic or porcelain coated by the manufacturer, some are even nickel plated.

If you decide to take on the project, I've outlined some steps you can take below to ensure it's done right:

  1. Remove the burner grates from your stove. Place each burner in its own sealable bag or container.
  2. Add 1 cup of ammonia to each bag or container. Add enough water to cover the burner as it sits flat against your table or counter. Seal the containers.
  3. Allow the grates to soak in the ammonia/water mixture overnight; this cleaning mixture will dissolve rust, grime, food buildup and other contaminants.
  4. Remove the grates and rinse them in clean warm water to wash away ammonia and loosened contaminants. Scrub with a non-metallic scouring pad to remove any remaining contaminants.
  5. Thoroughly dry the grates to prevent rust buildup.
  6. Coat each burner grate using the paintbrush and the temperature-resistant paint. Follow product instructions regarding application, as some products might require multiple coats or have varying drying times.
  7. Allow the paint to dry completely before returning the grates to the stove-top.

Note: Only use ammonia in a well-ventilated area, as the fumes are toxic if inhaled in large amounts.

I wish you all the best on the refurbish of the grates, you may try Sears.com and see what kind of heat-resistant paint may be offered, I know we carry products/items like that in retail.

If you have any further questions or inquiries, please don't hesitate to ask. Thank you for using ManageMyLife.com.

Read More
Jeff Wallace Sr -
Sears Technician
August 12, 2013
Q:

Can I paint the grates for my Kenmore gas range, if so does Sears have a paint available? 79075851302 Kenmore Gas range

A:

Thank you for the inquiry and for using ManageMyLife.com. I can definitely appreciate wanting to refurbish the grates, as cast-iron grates can become quite an investment to replace as they are costly to produce.

You may refinish the grates, as long as you use temperature-resistant paint, standard paint won't work because of the heat they have to endure. Typically they are cermaic or porcelain coated by the manufacturer, some are even nickel plated.

If you decide to take on the project, I've outlined some steps you can take below to ensure it's done right:

  1. Remove the burner grates from your stove. Place each burner in its own sealable bag or container.
  2. Add 1 cup of ammonia to each bag or container. Add enough water to cover the burner as it sits flat against your table or counter. Seal the containers.
  3. Allow the grates to soak in the ammonia/water mixture overnight; this cleaning mixture will dissolve rust, grime, food buildup and other contaminants.
  4. Remove the grates and rinse them in clean warm water to wash away ammonia and loosened contaminants. Scrub with a non-metallic scouring pad to remove any remaining contaminants.
  5. Thoroughly dry the grates to prevent rust buildup.
  6. Coat each burner grate using the paintbrush and the temperature-resistant paint. Follow product instructions regarding application, as some products might require multiple coats or have varying drying times.
  7. Allow the paint to dry completely before returning the grates to the stove-top.

Note: Only use ammonia in a well-ventilated area, as the fumes are toxic if inhaled in large amounts.

I wish you all the best on the refurbish of the grates, you may try Sears.com and see what kind of heat-resistant paint may be offered, I we carry products/items like that in retail.

If you have any further questions or inquiries, please don't hesitate to ask. Thank you for using ManageMyLife.com.

Read More
Jeff Wallace Sr -
Sears Technician
August 12, 2013

Top Parts