Model #79075731892 KENMORE Free Standing, Gas

  • Backguard
    3 Results
  • Burner
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

How do i light the pilot inside my oven?

A:

Unfamiliar appliances can be confusing if you need to determine if it is working correctly. I attached two links below that may help while you wait for the expert. The second link has parts and I see a manual is available for ordering. I hope this information helps.

Read More
Barbara H. -
February 02, 2012
A:

Thank you for your question and I understand your concern.

You range does not have a pilot light. It uses an electric glow bar igniter that must be provided 120 volts and it must glow red hot before the oven gas valve will open. The broil ignition system works the same way. Open the oven door and start a broil cycle and watch the operation. The bake operation should operate the same way.

In order to access the bake burner and bake igniter will require removing the oven bottom inside the oven cavity. Remove the oven racks and the two screws located at the back of the oven bottom. Lift the bottom panel up and then slide it back to clear the front lip and remove the oven bottom. Below the oven bottom will be another panel to remove before you can access the bake igniter.

If the bake igniter is glowing red, the igniter is weak and needs to be replaced. If the igniter is weak; it will not pull enough current/amperage to cause the gas valve to open.

If the igniter is not glowing; it could have a broken igniter, faulty gas valve or a faulty oven control. I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
February 04, 2012
See more answers
Q:

have a sears kenmore stove and the oven burner does not ignite, pilot is on. all burners including the broiler in oven works.

A:

I understand your Kenmore Stove is not igniting but the pilot is on and I bet this is a frustrating situation. I found a question in Manage My Life under the Answers button that is similar to the one you asked. This question will give you some general advice, while your waiting on an expert answer. I attached the link below, I hope this helps!!!!!!!!

Read More
Raquel F -
September 27, 2010
A:

The glow bar ignitor is likely too weak to cause the gas valve to open. If the ignitor does not pull enough electrical current when it is glowing, the gas valve will not open. It is possible the gas valve may have failed but this usually turns out to be an ignitor problem. To determine for sure which part has failed, will require the use of a meter that can measure amperage. A technician may be needed to make this type of check. I'm listing a site you can access, to have a tech come out. Here is a link for the website: Sears Home Services . If you would like more assistance, additional details will be helpful.

Read More
Scott D -
Sears Technician
September 28, 2010
See more answers
Q:

Kenmore Gas Range

A:

"Provide your model number to get you more detailed information specific to your product" Thanks!

Read More
Dezeray S -
August 17, 2010
A:

Thank you for your question.

In order to give you exact information on your gas range I will need the complete model number.

  • It is located behind the storage drawer face on the leg support of the chassis. It could start with: 362.xxxxx 911.xxxxx. 665.xxxxx. 790.xxxxxx.

  • It could be the Hot surface igniter or the safety valve. By having the model number I can give you some accurate information.

Read More
Sam A -
Sears Technician
August 17, 2010
A:

The model number was provided via email from Banderwax: 790.75731892

Read More
C Corniuk -
August 17, 2010
A:

Hello, any more advise on fixing this problem ?

Read More
Banderwax -
August 18, 2010
A:

Reviewing your question know with the complete model number 790.7573182 . The problem will be the HSI hot surface igniter, is that works in tandem with the gas safety valve. As the igniter heats to approximately 2100 degrees it will know pass enough electricity to operate safety gas valve and deliver gas to the oven bake burner. If the HSI is not heating up enough it will cause delayed ignition and operate erratically, and the oven will not heat or maintain proper baking. The part number for the ignitor is: 5303935066. To replace the ignitor, dissconnect power to the range and remove the oven door as illustrated in the owners manual. Remove the bottom oven cavity floor by un-screwing the two silver thumb screws by the back wall of the oven bottom and pull up and back to remove the oven bottom. Locate the bake hot surface ignitor next to the bake burner tube. Remove the two screws that secure the ignitor to the burner assembly. Continued

Read More
Sam A -
Sears Technician
August 20, 2010
A:

Pull the wire harness from the oven linePull the r and remove the plastic connector from the old ignitor and install new ignitor. PLEASE handle the new ignitor carefully. As you will see it will be packed in foam to prevent damage. If you drop the ignitor you can damage it beyond repair and it will have to be replaced. Re-install the floor bottom and test range for operation. I hope this helps.

Read More
Sam A -
Sears Technician
August 20, 2010
See more answers

Top Parts