Model #79075721991 KENMORE Free Standing, Gas

  • Backguard
    3 Results
  • Burner
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

how to change oven ignitor 79075721991 Kenmore Gas range

A:

Thanks for the inquiry and for using SearsPartsDirect.com.

I have outlined below the steps that will need to be taken to remove the oven's bottom panel and flame spreader in order to gain access to the ignitor, hopefully this will help. 

Disconnect the power cord from the range and remove the oven racks. Remove the two thumb screws located on the rear of the oven bottom. Lift the back up and slide the panel back until it clears the front of the frame and lift the front up and remove the panel. 

Once the oven bottom panel has been removed you will see the flame spreader. The flame spreader is usually held down to the burner with a single nut. Remove the nut and lift the flame spreader up and out to access the igniter. The igniter will be located towards the back of the burner assembly. 

Let us know if we can be of any further assistance and thanks for using SearsPartsDirect.com.  

Read More
Jeff Wallace Sr -
Sears Technician
November 26, 2013
Q:

Bottom of oven 79075721991 Kenmore Gas range

A:

Thanks for the inquiry and for using SearsPartsDirect.com.

I have outlined below the steps that will need to be taken to remove the oven's bottom panel and flame spreader in order to gain access to the ignitor, hopefully this will help. 

Disconnect the power cord from the range and remove the oven racks. Remove the two thumb screws located on the rear of the oven bottom. Lift the back up and slide the panel back until it clears the front of the frame and lift the front up and remove the panel. 

Once the oven bottom panel has been removed you will see the flame spreader. The flame spreader is usually held down to the burner with a single nut. Remove the nut and lift the flame spreader up and out to access the igniter. The igniter will be located towards the back of the burner assembly. 

Let us know if we can be of any further assistance and thanks for using SearsPartsDirect.com.  

Read More
Jeff Wallace Sr -
Sears Technician
November 26, 2013
Q:

can you help me with my stove door not opening

A:

Having a properly working range is very important. The stove door not opening can be very frustrating. I found some information for you that I am hoping will help you with the stove. I am adding the link below to help you with your question while you wait for your expert response. It may take 24-48 hours. I do hope that this will help you.

Read More
Marc -
December 16, 2012
A:

I recommend that you try to start a new self clean cycle. Give the control about 3 minutes to go through the locking process and get to the point where the oven would begin to heat. Cancel the self clean cycle at that point and see if the control will unlock the oven door. If not, then I recommend that you unplug the range for 5 minutes to reset the control. You can shut off the house circuit breaker for the range if that is easier than reaching the electrical outlet. Power the range back up and set the clock. Try the same procedure again. Set the self clean cycle and then cancel it after about 3 minutes. This may unlock the oven door so that the control will work normally. If not, then you could have a problem with the oven door lock assembly or the electronic control board. A wiring failure would also prevent that oven door lock from operating. I recommend that you have a service technician diagnose and repair that type of failure. You can schedule service through this link: Sears Home Services .

If you need more help or you want to diagnose that failure and fix it yourself, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
December 18, 2012
See more answers

Top Parts