Model #79075711893 KENMORE Free Standing, Gas

  • Backguard
    3 Results
  • Burner
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

How to light 79075711893 Kenmore Gas range

A:

Thank you for choosing SearsPartsDirect.com. I will be more than happy to assist you. I can understand any frustration you may have experienced with regards to your unit. Let’s see what we can do for you.

Looking at the information I have found a link that will help with the pilot on the top burners. I’m showing for the bake and the broil there are glow bar igniters that with glow to ignite the gas. Click here to view the information on the link i have foun.

Hope this information has helped you. If you are not comfortable doing this repair you can click here to schedule a technician or call toll free 1-800-469-4663. Again, thank you for choosing SearsPartsDirect.com.

 

Read More
JeffwallaceIII -
Sears Technician
January 20, 2015
Q:

oven burners will not heat null

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com

 I am sorry and do understand your frustration when the burners to the oven aren't working.

Glad to help out.   Im  looking at your model number 790.75711893.

 The upper and lower ignitors you say are lighting but not well enough.  

Pull the oven door down.   Turn on the bake ignitor for baking.   Even though it comes on, look and see how long it takes to come on.  IF it takes more than 2 minutes for either unit to light then needs to be replaced.  Also if the lighting is more like a dull red then not drawing enough current to operate the valve.  

 Instructions on cleaning ignitor:

1.  Please remove the racks from inside the oven.  

2.  Locate the ignitor on the back bottom side.

3.  Unscrew the screws that holds the ignitor to the oven and pull out the wire clip.  The ignitor is fully disengaged and now can be removed from inside the oven.

4.  Soak the ignitor in a plastic container filled with solvent.  Soak it for around 20 minutes.

5.  Take out the ignitor from the solvent and try to dry with a paper towel carefully.

6.  Spray your ignitor with a can of compressed air so it will remove any left over particles.  Then just reinstall the ignitor by the way that you removed it.

 

I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link below to be taken to the page.

bake ignitor for model 790.75711893

broil ignitor for model 790.75711893

gas valve  for model 790.75711893

 If you have further questions please let me know.

Thanks for choosing Sears PartsDirect.com

 

Read More
Larry L -
Sears Technician
September 05, 2013
A:

both igniters are getting red to white hot in about 20 seconds, gas still does not come out to burners. whats next?

Read More
Philip -
September 05, 2013
A:

Hello glad to help Philip.  Thank You for choosing Sears PartsDirect.com
 
You say both ignitors are doing their job though still faulty.   The next step is looking at your regulator.    It can cause this problem though hardly ever goes bad.  Take a look at it and check out the vent hole to see if it is clogged up.   Clearing it sometimes works out well.
 
 The regulator is what regulates the amount of gas in your oven.
 
A picture of the regulator on the link below it is key number 14.
 
 
 
 If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com

 
 

Read More
Larry L -
Sears Technician
September 05, 2013
A:

getting gas through regulator. stove top burners work fine. not getting gas to boiler burner or bake burner.

Read More
Philip -
September 05, 2013
A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com

Sorry took so long to get back with  you Philip.   I talked this over with everyone who has worked here and all agree that it should be either the igniter burners or the gas regulator.  You are telling me the burners are going on and lighting as they are supposed too and if it isn't the regulator.   I am sorry but see no other part so I will advise you the next step.  

 Allow us to show you the BEST our www.ManageMyLife.com website has to offer! Not only is this completely free, but we have troubleshooting experts who can provide you with tons of information from installing a part to maintaining your closest. In order to join our growing community of do it yourselfer's all we need is your email address and zip code and you're all set!

If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com
Read More
Larry L -
Sears Technician
September 06, 2013
See more answers
Q:

Kenmore Gas range model # 790.75711893

A:

I can understand your need for some type of instructions on how to properly open the top of your stove. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner.

Read More
Julio -
July 16, 2013
A:

Thank you for submitting your question. I understand your concern and I will be happy to assist you. First, disconnect the power from the range before performing any repairs. Then remove the grates, burner caps and the drip pans from the range top. You will then see three screws on each burner base securing the burner base to the top of your range. NOTE: Use caution when removing the screws or they could snap. Loosen and run the screw out but if it gets tight, run the screw back in and then out. You may have to do this 2-3 times before the screw will come out safely. Open the oven door and remove the screws along the bottom of the top securing the top to the frame. Lift the front of the top up a little and slide it forwards and remove the top. Make sure that the burner assembly does not hang up on the top when removing or you could damage the gas lines.
You will likely have to disconnect the burner from the gas supply line at each burner. Flip the burner over and you will see the screw securing the igniter to the bottom of the burner. Pull the igniter wire off of the igniter and reverse the procedure. I hope this helps. Please reply back to this thread if you require further assistance. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
July 18, 2013
See more answers

Top Parts