Model #79075193300 KENMORE Free Standing, Gas

  • Backguard
    3 Results
  • Burner
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore gas oven, takes too long to preheat

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Alina -
December 01, 2012
A:

Thank you for your question and I understand your concern.

Based on your symptom and details; the glow bar igniter is weak. The igniter must pull enough current/amperage to open the oven gas valve. When it gets weak it will take the gas valve along time to open and supply gas to the bake/broil burner.

Replace the glow bar igniter and your oven will operate properly again.

You can order the oven igniter #5303935066 at Sears Parts Direct. NOTE: Disconnect the power cord from the power source before servicing.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
December 03, 2012
A:

Hello Lyle. 45 minutes preheat time so figured ignitor was bad. Ordered the new ignitor. Spliced wires from new ignitor to those in oven but ignitor does not glow. Checking at the splice, there is no power. There is power to the rest of the oven-- the broiler ignitor works, clock etc. Wondering if in moving wires around I could have disrupted a connection down below the bottom shelf of oven. Is there a coupling below there that could have come unplugged? I started to remove the screws to release pan to see if I could get a look at the wires, but figured I had better not go further without advice. Any ideas? Repair person scheduled to come on Thurs (this is Monday evening). If I need to remove that pan, do you have instructions you can post? Thanks!

Read More
michael -
October 07, 2013
A:

Michael; without having the mode number of your gas range, I can't be certain if the oven bottom is easily removed or not. Look at the oven floor and see if there are a couple of screws at the back of the oven floor. If so, remove the two screws and then lift the back of the oven floor up and slide it back to clear the front lip of the oven frame and then lift it out. You can then follow the wires to the gas valve to see if one was pulled off. If all the wires are connected and you do no measure any voltage across the two wires connected to the igniter, it could have faulty oven control board, or a faulty oven safety valve. Reply with the model number if additional information is needed.

Read More
Joey S -
Sears Technician
October 14, 2013
See more answers
Q:

kenmore model 790 gas range. the gas stove top burners stopped sparking. what parts do I need to repair?

A:

Managemylife.com is a great place to find the answers to just about anything, especially on a range . I would suggest that you provide the model number of your product so your expert will be able to provide you the best possible answer. Share any insightful information that could be helpful. Continue this existing thread. Just click on the reply box below and provide that information

Read More
Yadira B -
August 13, 2012
A:

Thank you for your question and I understand your concern.

As Yardira suggested in the first response; adding the complete model number would be most helpful in providing model specific information and instructions.

Generally speaking, if all the electrodes quit sparking at the same time, it could have a faulty spark module or the L1 (line one) or the neutral wire has come loose or disconnected. Whenever any one burner knob is turned to the "light" position, the Line One (L1) circuit is completed to the spark module at which time the spark modules causes the sparking between the electrode and the grounded base of the burners. In order to properly diagnose the failure will require checking for a loose or disconnected wire in the circuit between the spark switches on top of each burner valve and at the spark module. Next, the voltage supply should be checked and confirmed at the spark module when the burner valve is set to the "light" positions. Turn the gas supply off to the range before checking voltages. NOTE: I do not recommend measuring voltage unless you have experience and feel safe and confident in doing so; otherwise I recommend calling service.

So that's what I can tell you at this point. I can give you more detailed help if you could provide me with the complete model number. If you could supply me with that information I will be happy to assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
August 14, 2012
A:

complete model #79075193300

Read More
heath -
August 14, 2012
A:

Heath; thank you for replying with the model number. The first and easiest component to check is to see if the spark module is getting 120 volts when the burner knob is turned to the "Light" position. There must 120 volts measured across the red and black wires connected to the spark module. The spark module is located behind the rear panel at the back of the range. You will need a voltage meter and you will also need to turn the gas supply valve off at the source. If voltage is measured, the spark module is faulty. Let me know if you need any further assistance. I also added an image of the wiring diagram and schematic. I traced the circuits for you. Note: I do not recommend measuring voltage unless you have experience and feel safe and confident in doing so; otherwise I recommend calling a service technician.

Read More
Joey S -
Sears Technician
August 15, 2012
See more answers

Top Parts