Model #79047919602 KENMORE ELITE Built-In Oven, Electric

  • Control Panel
    3 Results
  • Upper Oven
    3 Results
  • Lower Oven
    3 Results
  • Doors
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore Wall Oven

A:

Managemylife.com is a great place to find the answers to just about anything, especially on appliances. I would suggest that you provide a little more information such as the make and complete model number of your product so your expert will be able to provide you the best possible answer. Just click on reply below where you can provide the additional information.

Read More
aashe -
December 16, 2011
A:

You will normally need to hold that fan motor shaft stationary when removing the nut from the front of that fan blade. There is not usually a special tool that you need. Reply with the model number of your range and more information about the fan that you are removing for more help with that problem.

The problem with that bottom dishwasher drawer popping open during operation will usually need to be examined and repaired by a service technician. Here is a link for the Sears Service website: Sears Home Services . If you want to perform some troubleshooting on that problem yourself, reply with the full model number of your dishwasher.

There is normally a replacement water line part listed on the Sears PartsDirect website that will fix your water leak in the refrigerator. You can visit that website and check for the part that you need. If you need more help with that repair, reply with the full model number of your refrigerator.

Read More
Lyle W -
Sears Technician
December 19, 2011
A:

Lyle, thank you so much!!! My oven model is 790.47919602. I got the nut and blade off and compared it to the blade on our other unit. the only thing that looks different is that there is a flat portion in the center of the blade where the shafe connects with the nut. My dishwasher model is 465.13339600. The refridgerator is 795.77569600.

Read More
Lisa -
January 03, 2012
A:

Hello Lisa. Thanks for adding those model numbers. On the rattling fan, you can try replacing that fan blade to fix the rattle. I can't be sure that replacing that fan blade will fix your problem without being able to physically examine the unit but that may work. You can order parts from the Sears PartsDirect.com website (see link below). That dishwasher drawer problem should probably be looked at by a technician. There is a possibility that you have problems with hoses in back or with the lid on that drawer. We can provide technical information and repair tips but trying to fix that failure yourself is risky. Let me know if you really want to pull that drawer out and apart and I will provide more you with some tips. For the leaking water line on the refrigerator, there are kits available for the installation of a new water line. You may not need that type of kit since your water line is already installed. Depending on the location of your leak, you may need to replace the supply water line or you may need to order a part and replace an internal water line in the refrigerator. Reply with more information about where that water leak is located on your refrigerator and we will assist you further with that issue.

Read More
Lyle W -
Sears Technician
January 04, 2012
A:

Lyle, you ROCK!!! I ordered the fan for the oven and the rattle is gone!!! The hose that was ordered from the Sears parts warehouse was the wrong size so I will correct that today. I really do want to pull out the bottom drawer of the dishwasher so any technical expertise you provide will be greatly appreciated.

Read More
Lisa -
January 09, 2012
A:

Hello Lisa. Glad to hear that you got that fan rattle fixed. The dishwasher repair may be more challenging. I provided some technical information for that dishwasher in the image below. You can SHUT OFF THE HOUSE CIRCUIT BREAKER for the dishwasher to disconnect electrical power and carefully remove that drawer to check the components and try to determine the cause of your problem. NOTE: When you pull the drawer out you will normally need to turn it upside down to view components on the bottom of that drawer. Pay close attention to which way that you rotate the drawer (clockwise or counter-clockwise) because the drawer will need to be properly rotated back in the opposite direction when reassembling the dishwasher. This is necessary to make sure that the hoses are not twisted. If the drawer was removed during previous service and was not rotated back properly, this could be causing the drawer to pop open during operation. A problem with loading the dishwasher could also cause the lid to not close properly. Check that issue as well. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
January 10, 2012
See more answers
Q:

What went wrong when an F10 error came up while I was cooking two bake potatoes?

A:

The F10 error displayed indicates the control has sensed an over temperature condition. This means the control relay has stuck or the oven sensor is shorted.

One thing to try first is to unplug the oven for a few minutes and then plug it back in. If it starts to heat then the relay is stuck and you will need to replace the control.

If the oven doesn't heat then try to use it. If the error comes up after a few minutes then most likely the sensor if shorting out when it gets hot and replacing the sensor will most likely solve this problem.

Try this and if you need further assistance then submit another question with any additional details for further assistance with this problem.

Read More
Fred M -
Sears Technician
July 21, 2009

Top Parts